NGK AB6 18mm sparking plug. short reach (approx. 1/2'' /12mm). supplied with washer 
Champion D16 18mm sparking plug. short reach (approx. 1/2'' /12mm). supplied with washer 
9 piece AF hexagonal socket set for most general workshop use. drive size 3/8".sizes 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", 3/4" across flat
a good value workshop set
double depth brass hegagonal manifold nut, 
brass wing nut 5/16'' BSF thread (22 TPI). OR 5/16"BSW thread (18 TPI), marked number 4, 38mm wide x 23mm high 
replacement cylinder sleeve for engine block. we have two make batches available with very slightly differing dimension.Hepolite make - length 152.5mm, outside diameter of cylinder 66.0mm, inside di
rabbit eared windscreen wing nut, approx 39mm wide, supplied in fine bronze cast finish (not plated). 1/4'' BSF thread. (1/4 x 26tpi)
rabbit eared windscreen wing nut, approx 39mm wide, supplied in fine bronze cast finish (not plated). 5/16'' BSF thread. (5/16 x 22 tpi)
rabbit eared windscreen wing nut, approx 39mm wide, supplied in fine bronze cast finish (not plated). 3/8'' BSF thread. (3/8 x 20 tpi)
this very versatile black tape has many uses including moisture proof cable repairs, metal pipe work protection against corrosion particularly at welds and joints, repair of split or leaking radiator 
14 piece AF spanner set in holder pouch. satin chrome finish spanners which are open end at one end, ring spanner at other. drop forged hardened and tempered. chrome vanadium steel.sizes 1/4", 5/16"
6 piece AF spanner set in clip holder. satin chrome finish spanners which are open end at one end, ring spanner at other. drop forged hardened and tempered. chrome vanadium steel.sizes 3/8", 7/16",
8 piece BSW Whitworth spanner set in holder pouch. chrome finish spanners which are open end at one end, ring spanner at other. drop forged hardened and tempered. chrome vanadium steel.sizes 1/8", 3
we offer a kit for the repair of old cracked and crazed steering wheels, enabling refurbishment to high standard. the kit comprises cleaner, epoxy filler, abrasive pads and lacquer paint. full instruc 
wheel or spoke cleaning brush, wooden handle, long round bristle brush for getting through the spokes on wire wheels, approx 425mm long ball joint
brass body adjustable ball joint. non detachable, 1/4" x 1/4" BSF threads. has a cross pin to retain a screw adjuster in the end.
brass body adjustable ball joint. non detachable, 3/16" x 3/16" BSF threads. has a cross pin to retain a screw adjuster in the end.
brass body adjustable ball joint. non detachable, 10/32" UNF thread into body x 1/4" UNF thread on pin. has a cross pin to retain a screw adjuster in the end. 
steel adjustable ball joint, plated finish. non detachable, 5/16"x 5/16" BSF threads, has a cross pin to retain a screw adjuster in the end.
steel adjustable ball joint, plated finish, non detachable, 3/16 x 3/16" BSF threads, has a cross pin to retain a screw adjuster in the end.
steel adjustable ball joint, plated finish. non detachable, 1/4" x 1/4" BSF threads. has a cross pin to retain a screw adjuster in the end.
steel adjustable ball joint, plated finish, non detachable, 3/8” x 3/8” BSF threads (not plated), has a cross pin to retain a screw adjuster in the end. 
steel adjustable ball joint, plated body. 1/4" x 1/4" BSF threads
steel adjustable ball joint, plated finish, non detachable, 3/8” x 3/8” UNF threads, has a cross pin to retain a screw adjuster in the end. 
Amal type adjustable ball joint end, plated brass body. we offer 1/4" x 1/4" BSF thread onlyfuel tank sealant
a resin in solvent based fuel tank sealant for lining the internal of tanks. it is essential that the tank is removed and steam cleaned thoroughly before the application. further details on telephone greasers and oilers - cup oiler
larger angled flip top cup oiler. thread 1/8" BSP.we have various sizes - limited quaitities.
body measures approx 30mm tall x 19mm - one only
body measures approx 25mm tall x 16mm - one only
small angled flip top flap oiler, 1/4"BSF thread 
medium angled flip top flap oiler, 1/8"BSP thread 
flip top flap oiler, nickel plate finish, 3/8" hexagon, 1/4" x 26 TPI thread. 
flip top flap oiler, nickel plate finish, 7/16 hexagon, 1/8" BSP thread. 
flip top flap oiler, nickel plate finish, push fit into a 3/16" hole. 
flip top flap oiler, nickel plate finish, push fit into 1/4“ hole. 
small flip top flap oiler, self colour brass finish, 1/4" (6.6mm) hexagon, 1/4" x 26 TPI thread (1/4"BSF), only 5.8mm tall.we offer pack of 100 piece at discounted price of £110.00 pack
Winkley pattern oiler, nickel finish. 5/16" x 26 TPI thread x 22mm tall overall. these are usually fitted horizontally and the outer sleeve turns to cover the oil hole. this thread will recut to 5/1 
Winkley pattern oiler, nickel finish. 1/4" BSF thread (26 TPI) x 18mm tall overall. these are usually fitted horizontally and the outer sleeve turns to cover the oil hole. 
Winkley pattern oiler, nickel finish. 1/8 BSP thread x 23.5mm tall overall. these are usually fitted horizontally and the outer sleeve turns to cover the oil hole. 
Winkley pattern oiler, nickel finish. 3/16" BSF thread (32 TPI) x 18mm tall overall. these are usually fitted horizontally and the outer sleeve turns to cover the oil hole. 
Winkley pattern oiler, nickel finish. 5/16" BSW thread (18 TPI) x 20mm tall overall. these are usually fitted horizontally and the outer sleeve turns to cover the oil hole. greasers and oilers - greasers
brass screw down cup greaser with clicker action in lid, cap size 16mm diameter x 11mm deep, 5/16"BSW thread. height when fitted approx 18mm. 
new old original brass screw down cup greaser, type RC6, cap size 19mm diameter x 15mm deep, 5/16"BSW thread, clicker action in lid, lid marked Rotherhams Coventry RC6 
screw down cup greaser, type Kingfisher - No3 - nickel plated cap 33mm diameter x 19mm deep marked Kingfisher Leeds etc. 1/4" BSP thread on steel base. stands up approx 33mm when fitted.
brass screw down cup greaser, type RC1, cap size 35mm diameter x 26mm deep, 1/8" BSP thread only. stands up approx 45mm when fitted. 
brass screw down cup greaser, type RC11, cap size 11mm diameter x 11mm deep, 1/4" BSF thread. 
bass screw down cup greaser, type RC5, cap size 28mm diameter x 17mm deep, 1/8" BSP thread. 
brass screw down cup greaser, type RC6, cap size 19mm diameter x 15mm deep, 1/8" BSP thread. 
Enots type grease/oil nipple, 1/8” BSP thread, nickel plated 
Enots type grease/oil nipple, 5/16" BSF thread, nickel plated 
twist on cap, nickel plated. 
brass hexagonal flat top TAT type, grease nipple, 3/8" BSF thread. 
brass flat top grease nipple TAT type, 5/16"BSF thread 
brass hexagonal flat top TAT type, grease nipple, 1/4" BSP thread
brass hexagonal flat top TAT type, grease nipple, 1/8" BSP thread 
brass hexagonal flat top TAT type, grease nipple with 10mm thread 
hydraulic grease nipples, threads 1/8"BSP, 1/4"BSF, 5/16"BSF, 3/8"BSF, 1/4"UNF, 5/16"UNF 
brass hexagonal flat top TAT type, grease nipple with 6mm thread 
brass hexagonal flat top TAT type, grease nipple with 8mm thread 
hydraulic grease nipple, theads 1/8"BSP, 1/4"BSF, 5/16"BSF, 3/8"BSF, 1/4"UNF, 5/16"UNF
extenede type brass hexagonal flat top TAT type, grease nipple, 1/8" BSP thread x 26mm length (not including thread) 
1/8'' Right angled hexagonal grease nipple. greasers and oilers - gun and adaptor ends
large brass oil syringe with long spout and T handle, an invaluable tool for anyone whose car has an awkward-to-get-at gearbox or rear axle filler. body 40mm dia x 340mm long, overall length 550mm. 
medium brass oil syringe with short spout and T handle, an invaluable tool for anyone whose car has an awkward-to-get-at gearbox or rear axle filler. body 35mm dia x 193mm long, overall length 310mm. 
grease gun complete with rigid & flexible connectors 
'push on' grease gun adaptor for flat top grease nipples,( TAT type ) overall dimensions 30mm long, 20mm wide, provided with a female 1/8" BSP thread which will fit most grease guns. 
'pull on' grease gun adaptor for flat top grease nipples,( TAT type ) overall dimensions 30mm long, 20mm wide, provided with a female 1/8" BSP thread which will fit most grease guns. 
adjustable angle grease gun adaptor for flat top grease nipples (TAT type ) overall dimensions 55mm long, 28mm wide, provided with a female 1/8" BSP thread which will fit most grease guns. 
reproduction ENOTS type grease/oil gun adapter. made to be compatible to all standard oil or grease guns. 
push type grease applicator, supplied as shown. body measures 165mm x 41mm, overall 215mm long. 
side lever type pressure gun for oil application. supplied with stand end fitting for modern nipples, Enots fitting end to be ordered in addition if required. 
small brass oil syringe for topping up oil in gearbox or rear axle etc. approx 25mm diam x 215mm long (overall 247mm). offered with two spouts. new old stock, will show signs of age. styles can vary.jointings
pack of high quality brass shim stock. 6 inch wide (150mm approx) x 12 inch (300mm) long pieces of 8 different thickness.one each sheet of 0.001",0.002", 0.003", 0.004", 0.005", 0.006", 0.008" and 0
neoprene bonded cork gasket material stocked in sheet size 1000mm x 500mm.thickness available 1.6mm and 3.2mm
1.6mm thick - neoprene bonded cork gasket material. sheet measures approx 385mm diameter 
glass fibre heat insulation yarn for wrapping exhaust pipes etc. nominal 6mm diameter x 10 metre long roll. also offered in 3kg roll (approx 100 metre length) at £97.00
glass fibre heat insulation webbing, for wrapping around exhaust pipes etc. 50mm wide x 10 metre roll. also offered in 30 metre roll at £63.75
hard red vegetable fibre sheet for cutting washers etc from. supplied in sheet of 300mm x 300mm only. thickness 1/32" (0.8mm)
hard red vegetable fibre sheet for cutting washers etc from. supplied in sheet of 300mm x 300mm only. thickness 3/64" (1.2mm)
hard red vegetable fibre sheet for cutting washers etc from. supplied in sheet of 300mm x 300mm only. thickness 1/16" (1.6mm) 
selection of jointing offcuts of various sizes and item
hard white coloured compressed felt for cutting oil seal from. we supply in cut sheets 150mm square. (larger sheet sizes available on application)following thickness:
approx 4mm
approx 6mm
app
gasket paper jointing stocked in sheet size 1000mm x 500mm 
red fibre washers of imperial sizes, supplied as an assorted pack of approx 110 pieces, which should cover many automotive applications. approximate contents (sizes marked under in mm) covering 1/8" t 
Soft rubber cord. 1/8'' (3mm) dia. soft rubber sealing cordone each sheet of 0.002", 0.003", 0.004", 0.005", 0.006", 0.008", 0.010" and
vernier coupling
gunmetal Simms couplings, unmachined central drive hole available 14 or 15 teeth (48mm diameter), 19 or 20 teeth (57mm diameter) or 23 or 24 teeth (68mm diameter) 
small size 14/15 teeth, 48mm diameter. made to original pattern in hard rubber. 
large size, 23/24 teeth, 70mm diameter. made from hard rubber. 
large size 27/28 teeth, 78mm diameter. mde from hard rubber. 
Bosch, 8/9 peg type, pegs on 46mm diameter approx, external 60mm diameter, internal diameter 35mm, hard rubber 
Bosch, 15/16 peg type, pegs on 52mm diameter approx, external 65mm diameter, internal diameter 25mm, hard rubber. 
aluminium drive couplings complete. the unmachined drive and rubber coupling 27/28 teeth. suitable vintage Lancia and similar. dimensions approx 84mm diameter. 
larger size 19/20 teeth, 57mm diameter. made to original pattern in hard rubber yoke end
clevis pin and yolk for brake and control ends. 3/16" pin x 3/16" BSF thread - 3/16" between fork (nominal 4.5mm size), steel with pin. also available left hand thread at £6.20
clevis pin and yolk for brake and control ends. 1/4" pin x 1/4" BSF thread - 1/4“ between fork (nominal 6mm), steel with pin. also available left hand thread at £6.60
clevis pin and yolk for brake and control ends. 5/16" pin x 5/16" BSF thread, 5/16" (nominal 8mm) between fork, steel with pin. left hand thread also vailable at £7.70
clevis pin and yolk for brake and control ends. 3/8” pin x 3/8” BSF thread - 3/8" (nominal 10mm) between fork, steel with pin. left hand thread also available at £8.50
clevis pin and yolk for brake and control ends. 1/4" pin x 1/4" UNF thread - 1/4" between fork (nominal 6mm), steel with pin.
clevis pin and yolk for brake and control ends. 5/16" pin x 5/16" UNF thread, 5/16" (nominal 8mm) between fork, steel with pin.
clevis pin and yolk for brake and control ends. 3/16" pin x 3/16" UNF thread - 3/16" between fork (nominal 4.5mm size), steel with pin.
clevis pin and yolk for brake and control ends. 3/8” pin x 3/8” UNF thread - 3/8" (nominal 10mm) between fork, steel with pin.
clevis pin and yolk for brake and control ends. 1/4" pin x 5/16" UNF thread, 5/16" (nominal 8mm) between fork, steel with pin. note pin is smaller than thread on this item.
clevis pin and yolk for brake and control ends. 7/16” pin x 7/16” UNF thread - 7/16" (nominal 11mm) between fork, steel with pin. 
replacement clevis pin in following sizes, 3/16" (4.5mm) diam, 1/4" (6mm) diam, 5/16" (8mm) dia or 3/8" (10mm) at prices in drop box