dashboard
chrome top dash lamp, panel fixing through 19mm hole. basic switch incorporated with twist cap. 
pull out dash lamp, all brass construction, 57mm long with 51mm diam mounting flange. requires separate switch. 
cylindrical dash lamp, black bakelite type ends, chromium centre tube 25mm diameter and clip. 90mm long. 
bracket mount type dash or panel lamp. mounting plate 23mm x 65mm (can be cut smaller) with lamp fitted. stainless steel cover (pulls off to change bulb) and basis switch.application also Ford model
type DF41 lamp, chromium cowl with 'Lucas' emblem stamped on top, black flange (70mm x 37mm) fitting, 2 1/8" (54mm) mounting hole centres, supplied with cable and bulb. basic switch incorporated with 
nice dashboard lamp with helmet cover. fits through metal dash hole approx 17mm. overall 46mm tall x 26mm wide when fitted. top cover pulls off to change bulb. no switch in this unit. black finish onl 
nice dashboard lamp with helmet cover. fits through metal dash hole approx 10mm. overall 57mm tall x 25mm wide when fitted. top cover pulls off to change bulb. basic switch on stem side. dull plated c 
ignition warning lamp, chrome (slotted) screw bezel, black plastic body fits through dash (19mm hole), 
small panel mount warning lamp with metal rim which unscrews to change bulb. 13.4mm diameter. 12 volt 2 watt BA7 bulb fitted, push fit into a 13.4mm panel hole. twin wires to rear 
small panel mount warning lamp with metal rim 16mm diameter. 12 volt 2 watt BA7 bulb fitted, push fit into a 13mm panel hole. 6.3mm push on rear terminal connection. to change bulb the bulbholder simp 
dash or panel warning lamp with metal bezel (diameter 22mm). rear body black plastic, fits through 16mm panel hole (maximum 12mm thickness), secured with nut. wire screw terminals on rear.no bulb su
head and spot
classic Lucas SFT576 fog lamp, freestand base mount. approx 146mm diameter. block type glass lens with chrome centre knob, all chrome body. a quality reproduction item. supplied with 12 volt bulb 
classic Lucas WFT576 fog lamp, rear mounted. approx 146mm diameter. block type glass lens with chrome centre knob, all chrome body. a quality reproduction item. supplied with 12 volt bulb 
classic Lucas SLR576 spot/driving lamp, freestand base mount. approx 146mm diameter. plain glass lens with chrome centre knob, all chrome body. a quality reproduction item. supplied with 12 volt bulb 
classic Lucas WLR576 spot/driving lamp, rear mounted. approx 146mm diameter. plain glass lens with chrome centre knob, all chrome body.a quality reproduction item. supplied with 12 volt bulb. 
freestanding chrome plated headlamp unit fitted with 12 volt lamp unit (main/dip). lamps measure approx 182mm diameter x 140mm deep overall. single 12mm bolt mounting. supplied in pair (2 piece) only. 
freestanding long range beam driving/spot lamp approx 184mm across x approx 90mm deep. convex plain glass lens with central chrome knob as pattern and style of Lucas CLR700 lamp. single bolt mounting 
freestanding fog lamp approx 184mm across x approx 90mm deep. near flat block pattern glass lens as pattern and style of Lucas SFT700 lamp. single bolt mounting to base. polished stainless steel rim a 
classic Lucas 5FT Fog Ranger freestanding lamp. approx 156mm diameter. block glass lens, all chrome body. a quality reproduction item. supplied with 12 volt bulb 
classic Lucas 5WFT Fog Ranger rear mounted lamp. approx 156mm diameter. block glass lens, all chrome body. a quality reproduction item. supplied with 12 volt bulb 
classic Lucas 5FT Fog Ranger freestanding spot lamp. approx 156mm diameter. plain glass lens, all chrome body. a quality reproduction item. supplied with 12 volt bulb 
large polished stainless steel headlamp units. approx 255mm diameter x approx 135mm deep. single mounting bolt, cables enter from lower rear. patterned shallow dome glass lens. offered in 12 volt only 
headlamp bowl for standard 7" (700) units, plastic back shell (will not rust) complete with plated retaining rim holder, adjusters and bowl to body sealing ring/gasket 
free standing headlamp unit with single mounting stem bolt, metal bucket back, chrome rim, approx 190mm overall diameter. a solid and robust unit which has various applications. we offer this part in glass lamp unit fitted by works to allow base mounting of lamp.
small free standing headlamp unit with single mounting stem bolt, metal bucket back, all chrome, approx 150mm overall diameter. a solid and robust unit which has various applications. 12 volt seal b glass lamp unit fitted by works to allow base mounting of lamp
metal Lucas type headlamp bowl for standard 7" (700) units. three adjuster, supplied with metal back shell, chrome retaining rim holder, adjusters and bowl to body sealing ring/gasket 
replacement part Lucas PL style 700 (7") tripod bar headlamp unit. supplied with 12 volt halogen bulb. opening for side light bulb. RIGHT HAND DRIVE only. offered in pairs only (2 pieces) 
Lucas marked pre focus 700 headlamp unit for right hand drive (dip to left side), complete with metal wing mounting bowl, adjuster screws, 12 volt bulb, retaining rims and gasket seals. 
Raydyot base mounted spotlamp, chrome plate on brass lamp to original pattern, with adjustable mounting arm and bracket with handle. lamp 112mm dia x 93mm deep, handle 100mm x 25mm, mounting arm 50mm 
Raydyot pillar mounted spotlamp, chrome plate on brass lamp to original pattern, with adjustable mounting arm and bracket with handle. lamp 112mm dia x 93mm deep, handle 100mm x 25mm, mounting arm 11 
Raydyot pillar mounted spotlamp with rear view mirror made to original patten, chrome on brass. pillar mounted on adjustable mounting arm and bracket, lamp 112mm dia x 93mm deep, mirror 112mm x 29mm 
chrome body smaller driving lamps, approx 125mm diameter. single bolt (10mm) fixing with wire. shallow back as the total depth of the unit is about 70mm including the dome glass front. sold in 2 piece indicator
very small chrome warning/indicator lamp with amber lens. (40mm x 25mm x 40mm depth). please note that this unit accepts MBC bulbs, which do not have the watts available for 21w/42w electric flasher 
recessed lamp - rubber boot/body (approx 74mm diam) chrome rim, amber glass lens (25mm depth from mount pamel), Lucas model 488 with flat lens, mounts through 35mm panel hole. 
small lamp of modern manufacture particularly suitable for flashing indicator use. chrome plated body with amber lens. body approx 58mm diameter x 70mm long. single mounting stud. single contact BA15s 
polished stainless steel (110mm x 55mm x 80mm deep) with amber glass lens. single bolt fixing allows choice of mounting. H3 halogen bulb 12v x 20watt. 
flush back indicator lamp approx 72mm rubber back, stainless steel rim and amber plastic lens. uses a festoon bulb. a useful lamp where indicators are required without the need to cut large holes. two 
indicator lamp of vintage appearance, modelled to match the Lucas rear lamp type 582. amber plastic lens 55mm dia, body 58mm long x 42mm diam, overall length 92mm. black body. we have commissioned pro 
recessed lamp (approx 72mm diam) - rubber boot/body, chrome rim, amber glass lens (45mm deep). Lucas model 594 with raised lens. panel hole for fixing 35mm. 
torpedo style sidelamp, reproduction of the Lucas 1130 type, chromium plated body approx 100mm long x 38mm diameter, amber plastic moulded lens . double filament bulb holder (allows combined side and 
free standing chrome body rectangular indicator lamp with amber lens, lens 60mm x 45mm, 52mm deep, mounting by single 10mm bolt through which wire passes. fitted with 12 volt 21watt bulb. 
a neat rear lamp, with single mounting which can be supplied with a flat lens instead of the domed amber lens fitted, to give a lamp of vintage appearance, into which 5w bulbs only will fit. double co 
Lucas model SF80 semaphore trafficator, arm extends 7.1/4" (184mm) from pivot point. staybright cover, 12 volt only. new old unused Lucas stock number plate illumination
small metal covered lamp with opaque plastic lens for varios applications. base 70mm x 33mm, t screw fixings 51mm apart. lamp body protrudes approx 25mm
remanufactured reverse / number plate lamp of Lucas L469 pattern. chrome on brass with frosted main lens. 163mm x 40mm x 60mm deep. two mounting bolts to rear 77mm centres 
chrome cowl shields glass lens, as Lucas model type L534. base approx 60mm x 40mm. 
as Lucas model 467 as fitted to numerous vehicles. base 112mm x49mm x 45mm high, fixing studs 85mm centres, clear side lens.
parts and spares
acetylene gas burners for carbide lamps offered as shown. these are new old stock and the brass will show some tarnish marks. as shown on the bigger image:left - threaded base (taper thread from 6.
BRC lamp oval plate - engraved copper.marked B.R.C. lenticulaire parabolique No (space for entry) Generateur ALPHA
measures 59mm x 26mm
single ended bulb holder. dimensions thread diameter 19mm, overall length 38mm, flange 28.5mm, accepts BA15D bulb, rear nut removes to expose terminal contacts. double contact. 
useful bulbholder (BA15) with bracket, which can be bent as necessary. offered in single contact or double contact.
plug for SBC type holder, double contact. also offered in single contact.cables enter through back.
replacement general purpose bulb holder (accepts 15mm base bulb). offered for various bulbs configurations.single contact parallel pin, double contact parallel pin, double contact offset pin. (pin r
double contact bulbholder for our 297 (Lucas 1130) sidelamp, accepts double contact SBC Ba15d bulbs.please note these are made to original pattern.
reproduction CAV badge. nickel plate brass casting with lugs on rear to peen over and secure as original. we stock the following size (measured across outside of badge).22mm diameter.
please note that a smaller hole is required for fitting.
Chrome on Brass cover for the 265 lamp 
body to base gasket for D Lamp 
glass to body gasket for split lens D Lamp 
replacement acrylic D lamp red lens (Lucas 523307) for the Lucas box type 288-3 rear number plate lamp on the rear number plate box assembly. for chrome rim, clip, gasket and screw please see our part 
replacement red glass for split D lamp 
replacement chrome finish D lamp rim (Lucas 523333) for the Lucas box type 288-3 rear number plate lamp on the rear number plate box assembly. this is retained by a side hinge pin, and retained shut 
clear side lens for number plate window for D Lamp 
glass retaining wire for D Lamp 
shallow dome head lamp base repair kit. approx 11mm diameter across head, stem approx 4.5mm thread x 12mm long. polished stainless steel, supplied with hex nuts. per packet of 12 parts suitable for using fixing bonnet panels to hinge.
double contact holder which accepts a plug or standard SBC bulb at either end. threaded outside body. we also offer this item in single contact guise 
rubber rens O ring for our 297 (Lucas 1130) sidelamp. 
double contact headlamp converter for most Lucas headlamps which are mounted through the rear of reflector bowl (usually held in place with clamp clip not supplied). 
chromium rim catch for Lucas head lamps, long type, overall dimensions 45mm long x 26mm wide. 
chromium plated rim catch, for Lucas head lamps, short style, ooverall dimensions 31mm long x 27mm wide, use with wire 864 
chrome plate bracket. 
spring (spectacle shape only) for rim using short rim catch clip 
chrome plated screw stud and Butler type catch barrel.
hexagonal brass nut for headlamp, 5/8" x 26 tpi (fine thread). (approx 16mm bore) 
brass headlamp stud mounting nut for Lucas RB160, P100, P80 etc type lamp. thread 1/2" x 26 tpias Lucas part 500357
headlamp mounting bolt (hollow). thread 5/8" x 26 tpi ( fine thread). measures approx 68mm long x 16mm thread diameter. 
headlamp mounting bolt (hollow). thread 5/8" x 26 tpi ( fine thread) as original. measures approx 50mm long x 16mm thread diameter. 
headlamp mounting bolt (hollow) with loose collar. thread 5/8" x 26 tpi ( fine thread) as original. measures approx 50mm long x 16mm thread diameter. 
headlamp mounting bolt (hollow). thread 5/8" x 26 tpi ( fine thread) as original. measures approx 56mm long x 16mm thread diameter. 
P100, P80, RB160 headlamp mounting bolt. thread 1/2" x 26 tpi ( fine thread) as original. measures approx 85mm long x 13mm thread diameter (thread runs for 24mm). 
headlight peak for 7" lights, stainless steel, clips behind inner headlight rim. 
W wire clip to hold glass into headlamp rim, approx 35mm long 
large W wire for holding glass into rim, approx 60mm long side. this clip is actually made for P100 lamps. 
rubber lamp entry cable grommet. approx 13.5mm internal diameter. 
red dot Lucas medallion for our 297A (Lucas 1130) sidelamp. overall dimensions 14mm dia x 6.25mm deep, to fit 11.5mm hole. 
hexagonal nut for Lucas type lamps. 7/16" x 26 tpi (very fine thread) approx 11mm bore. 
lamp mounting bolt (hollow). thread 7/16" x 26 tpi ( fine thread) as original. measures approx 36mm long x 11mm thread diameter. supplied with hexagon nut. used on various Lucas spot and sidelamps. 
rubber mounting pad for our 787 (Lucas 516 sidelamp) 
large W wire spring clip for holding glass into rim. approx 62mm long side. useful for deep headlamp rims. 
large LUCAS enamel badge (4 colour), for tops of some larger Lucas lamps, 19.3mm wide x 22.5mm tall. offered in chrome or nickel (please specify). 
reproduction Lucas King of the Road badge. chrome plate (nickel to order) brass castings with lugs on rear to peen over and secure as original. we stock the following sizes (measure overall diameter o please note that a smaller hole is required for fitting.
MBC bulbholder, 12mm diameter, useful general application spare for minaiture base cap bulb, 
pre-focus headlamp connector with lead, double contact with three pin bayonet bulb holder, three wires with headlamp bowl sealing grommet and soldered bullet connecters, overall length 910mm. 
base mounting bracket for Raydyot spotlamp. (fits in place of side mounting arm). approx 65mm overal diameter, chrome on brass.
replacement side mounting bracket for Raydyot spotlamp. approx 106mm overall, chrome on brass.
spare clear side lens for round 'Pork Pie' rear lamp. 
all glass red lens for Duolamp lamp with embossed Stop on top part.
replacement red plastic lens with brass inner screw thread for our 288 lamp, equivalent to Lucas L582 
replacement glass lamp unit for Lucas type 576 lamps. supplied with bulbholder (no bulb). plain dome lens with chrome centre dot. order bulb separately - single contact type base P22s 
replacement glass lamp unit for Lucas type 576 lamps. supplied with bulbholder (no bulb). block pattern dome lens with chrome centre dot. order bulb separately - single contact type base P22s Ford part re
plastic front lens for our 297 (Lucas 1130) sidelamp. 
original pattern frosted lens with chrome rim for our 297 (Lucas 1130) sidelamp, overall outside diameter 47mm. 
replacement front glass lens for Raydyot spot lamp 570. measures 104mm diameter. 
replacement glass lens for 211 Duolamp, specify all red or split amber/red 
spare red glass lens for round 'Pork Pie' rear lamp, specify flutes running as picture vertical OR horizontal 
replacement red colour main front lens for lamp 
reproduction Rotax badge. chrome plate (nickel to order) brass casting with lugs on rear to peen over and secure as original. we stock the following sizes (measured across outside of badge).very sma
please note that a smaller hole is required for fitting.
sealed beam headlamp connector with lead, nylon block three lucar connector, three wires with headlamp bowl sealing grommet and soldered bullets, overall length 850mm. 
semaphore (orange) plastic blade to fit Lucas SF80 trafficator, (equivalent part 532026). overall length 180mm. 
polished stainless steel backing for SF80 trafficator. overall length 195mm. 
top rim retaining screw for Lucas 1130 type sidelamp. 
two bulb (yellow for flasher, clear for sidelamp) - 12 volt ONLY - bulbholder for fitting into Lucas type 1130 sidelamps. supplied in pairs only. 
small w wire clip for sidelamps, packet of 6 pieces 
replacement chrome plated lamp retaining rim for Lucas L471 type rear lamps 
domed red or amber main lens for our 257 lamp. base 60mm diameter measured overall. 
replacement side lens (44mm dia) for the rubber divers lamp, specify clear or red 
flat red or amber front lens (58mm dia) for rubber divers lamp, specify colour parts and spares - rubber parts
headlamp bowl to body rubber gasket for all two screw adjuster 7" (700 type) lamps. 
700 series headlamp glass to rim rubber dust gasket. 
rubber rear body (boot) for Lucas 488 model lamp. Ford part ref E0A-13216 
rubber rear body (boot) for Lucas 594 model lamp. 
flat rubber mounting pad for Lucas 1130 type sidelamp. rear
new complete lamp units as fitted to the ford 103E and 104E, comprising of new lens, new base with double contact bulb holder for rear and brake light (bulb reference No. B380 (12 volt) B382 (6 volt), 
angled wing mounting stop/tail lamp, as supplied by the ford motor co. for fitting to the E93A Prefect 1939 - 1948. supplied as a "ready to fit" lamp along with template for hole drilling, 61mm x 149 
Bulter rear lamp with number plate illumination window with mounting bracket. very small red lens (24mm dia). lamp body 40mm dia x 45mm deep. bracket as shown. please note that this lamp is not consi 
diver's helmet tail lamp. 5 cm lens diam and overall diameter about 9cm. similar to the old CAV, Rotax and Lucas models. sold in pairs, these superb lamps are available in either polished brass, brigh 
round rear lamp with split glass lens. polished stainless steel 97mm diameter x 51mm deep. two single contact bulbholders fitted through back, mounting screw hole centres 45mm. 
replacement reproduction front cover (face) of our manufacture for the Lucas type 312 'Owl Eye' rear lamp.these are chrome on brass. Lucas emblem fitted.
we supply these with the small red lens fit
stainless steel cover for rear of doulamp type lamp 
remanufactured rear lamp as Lucas type L494 part. chrome finish on cast body with chrome plated fittings. body size 140mm wide x 75mm high x 68mm deep. mounting stem approx 13mm. bulbholder BA15s.c
licence plate/number plate bracket which bolts under rear lamp. available in polished stainless steel or black enamel finish 
early pattern cylindrical rear lamp with side number plate illumination, as Lucas type 582. fitted with prismatic lens and screw on metal rim. 45mm dia x 93mm overall, body 42mm dia. - double contac 
recessed lamp - rubber boot/body (approx 74mm diam) chrome rim, red glass lens (25mm depth from mount pamel), Lucas model 488 with flat lens, mounts through 35mm panel hole. 
recessed lamp (approx 72mm diam) - rubber boot/body, chrome rim, red glass lens (45mm deep). Lucas model 594 with raised lens. panel hole for fixing 35mm. 
angle mounted rear lamp similar to Lucas 471 type glass lens approx 57mm deep, chrome bezel. base approx 127mm x 62mm. 
a useful rear lamp, which we would refer to as 'Miller type' lamp. used on motorcycles, but offering useful applications as additional number plate illumination etc. the prismatic red lens (32mm diame 
"Owl Eye" Rear lamp, reproduction from our own tooling of Lucas type 312 lamp, chrome plated finish on brass pressings, supplied with red with white or amber (as shown) main lenses. number plate illum 
single red lens duolamp, stainless steel rim 97mm diam, black body 60mm deep. one double contact bulbholder. with or without number plate illumination. 
steel rear lamp bracket suitable for divers helmet rear lamp and similar requiring spade mounting. this part is prefabricated and supplied undrilled. overall height approx 125mm. fitting to the car ( 
rear stop/rear lamp as Lucas L549 for mounting on to sloping rear wing panel. red plastic lens. chrome base plate with flat back rubber mounting pad. base 85mm x 142mm. applicable Morgan, MGA, Triumph TR etc,
mounting bracket (with rubber pad and bolts) for mounting 211/958 lamps away from wing. chromium plated. available for left or right of car. measurement long the 'underside' when fitted approx 105mm. ... 
round 'Pork Pie' rear lamp, as Lucas ST38, fitted with emblem. 90mm diameter x 65mm deep, these are made from brass body and rim, red glass lens. three single contact bulbholders. we offer this lamp w 
'D' Lamp full red glass lens, fitted with double contact bulbholder (for stop and tail lamps) brass body 92mm x 85mm x 60mm. clear side number plate illumination lens. black enamel finish. 
'D' Lamp full red glass lens, fitted with double contact bulbholder (for stop and tail lamps). brass body 92mm x 85mm x 60mm. clear side number plate illumination lens. chromium finish. 
early pattern 'D' lamp with split red glass lens, fitted with two bulbholders. brass body 92mm x 85mm x 60mm. clear side number plate illumination lens, black enamel finish. 
early pattern 'D' lamp with split red glass lens, fitted with two bulbholders. brass body 92mm x 85mm x 60mm. clear side number plate illumination lens, chromium finishplease note that we have a f
single red lens duolamp, stainless steel rim 97mm diam, stainless steel body 60mm deep. one double contact bulbholder. with or without number plate illumination. 
legal version of a very popular vintage Lucas rear lamp type 582 with side number plate illumination. red plastic lens 55mm dia, body 58mm long x 42mm diam, overall length 92mm. double contact equal 
polished stainless steel (110mm x 55mm x 80mm deep) with glass lens. single bolt fixing allows choice of mounting. H3 halogen bulb 12v x 20watt. choice of clear lens for a reversing lamp, or red lens 
rubber divers helmet lamp - approx 70mm diameter body, supplied with red flat main lens, clear side window. double contact bulbholder fitted, enabling use of double filament bulb. amber lens available 
a neat rear lamp, with single mounting which can be supplied with a flat lens instead of the domed red lens fitted, to give a lamp of vintage appearance, into which 5w bulbs only will fit. double cont we have a limited stock of new old part of original Rubbolite manufacture (as opposed to the remanufactured items) which we offer as an alternative at a higher cost of £29.40 each
round Rubbolite number 23 rear lamp - 91mm diameter at widest with raised red lens and side number plate illumination lens. two double contact bulb holders fitted offering various bulb applications. a 
small rear lamp with red plastic lens retained in an alloy housing.diameter 50m (lens retained in screw off alloy housing) and approx 50mm deep to fixing nut behind the brass body, tapers back to ap
round 'Pork Pie' rear lamp, as Lucas ST38, converted for combined stop/rear/indicator function. 90mm diameter x 65mm deep, split red/amber lens, with clear side lens. the bulbholders are modified to f rear - reflector
large chrome rimmed reflector approx 71mm diameter overall. single centre screw fitting as Lucas type RER14. rubber backing has slight curve to follow radius of panel. 
angled rubber red reflector, as Lucas type RER2, for mounting on to sloping rear wings etc. base measure approx 74mm diameter. we have a limited stock of new old part of original Lucas manufacture (as opposed to the remanufactured items) which we offer as an alternative at a higher cost of £11.50 each
round red reflector with deep chromium surround as Lucas type RER25, rubber back, flat, screw fixing. approx 51mm base diameter. also offered in polished brass. 
large flat back rubber surround reflector approx 90mm diameter. screw fixing around edge, for those who want reflectors that can be seen. 
red reflector, diam 58mm,integral threaded stud fixing. 
flat rubber surround for vertical surfaces as Lucas type RER6. self tapping screw for mounting supplied, approx 48mm base diameter. 
metal surround original Lucas reflector (42mm dia) with black metal painted side mounting bracket (7mm hole)ONE ONLY REMAINING 
rear red reflector with metal surround with rear mounting stud and nut supplied. approx 42mm diameter. 
red reflector with a shallow surround as Lucas type RER5, rubber back. screw/bolt, choice of chromium, nickel or polished brass rim. overall diameter of base approx 53mm. side
internally modified torpedo style sidelamp, reproduction of the Lucas 1130 type, chromium plated on brass body approx 100mm long x 38mm diameter, clear plastic lens held with screw in top, the interna 
reproduction CAV pattern Torpedo side lamps, nickel plate, with circular 'Toby' badge on top. knurled rim holding the clear curved bulls eye glass lens. these are made to the shape of the original CAV 
large sidelamp similar to Lucas type VS45, 90mm diameter x 85mm deep, with glass lens. we offer these lamps finished with black body/chrome rim, all chrome or all nickel. mounting bolt 14mm diameter. 
recessed lamp (approx 72mm diam) - rubber boot/body, chrome rim, clear glass lens (45mm deep). Lucas model 594 with raised lens. panel hole for fixing 35mm. 
recessed lamp - rubber boot/body (approx 74mm diam) chrome rim, clear glass lens (25mm depth from mount pamel), Lucas model 488 with flat lens, mounts through 35mm panel hole. 
reproduction of Lucas LD109 side lamp, approx 51mm diameter x 63mm long, with red medallion in top , frosted lens. can only be used as sidelight (MBC bulbholder)
torpedo style sidelamp, reproduction of the Lucas 1130 type, chromium plated body approx 100mm long x 38mm diameter, clear plastic moulded lens . double filament bulb holder (allows combined side and 
torpedo style sidelamp, reproduction of the Lucas 1130 type, chromium plated body approx 100mm long x 38mm diameter, frosted clear lens with chrome rim held with screw in top, double filament bulbhold 
torpedo style sidelamp, reproduction of the Lucas 1130 type, chromium plated body approx 100mm long x 38mm diameter, frosted clear lens with chrome rim held with screw in top, double filament bulbhold 
small chromium plated side lamp as Lucas type 516, fitted to A30, Morgan etc. 81mm long x 32mm dia. supplied with rubber mounting pad. uses MBC bulbs, max 3watt 
clear glass sidelamp with heavy chrome rim (approx 63mm overall). glass lens, rubber back boot supplied. accepts single contact MBC bulb. as fitted to early Morris Minor, Land Rover, Wolseley etc. no 
remanufactured side lamp to Lucas L490 pattern as used on Jaguar Mk2,early XK and Armstrong Siddeley amongst others as Lucas part 52474. clear patterned lens with chrome rim (30mm diameter x approx 7m 
remanufactured side lamp to Lucas L513 pattern as used on Jaguar XK150 and Daimler amongst others as Lucas part 52175. clear patterned lens with chrome rim (45mm diameter x approx 12mm deep) which fit 
torpedo shape sidelamp, brass body available in self colour or nickel plated. the domed glass lens on a screw rim. body 151m long x 76mm diameter, base 90mm x 31mm with mounting holes at 68mm centre
sundry
surface fitting, mounting holes 50mm centres, chromium plated base, prismatic glass lens, held with threaded knurled ring, 89mm diameter x 57mm deep. double contact bulb holder, excepts BA15d bulb (ou