universal battery clamp bracket to keep the battery well secured. long angled bar which pulls against to side of battery, screw thread adjuster rods for fitting end to holes in panel. 
distributor contact point set - Lucas 407050, which has very wide application. fits AC, Alvis, Austin, Bedford, Commr, Karrier, Daimler, David Brown, Dodge, Ferguson, Ford, Hillman, Humber, International, Jaguar, Jensen, Massey Harris, MG, Morris, Riley, Rover, Landrover, Singer, Standard, Sunbean Talbot, Triumph, Vauxhall, Wolseley etc.
distributor cap for late 105E model 1965 on. push in connections. also fitted to Ford Fiesta 1976 on, Ford Escort 1100/1300 1971 on, Ford Escort, Mexico, RS1800, RS200 1970 on, Corsair (1966-70), Cor 
distributor cap (side outlet) for Lucas distributors, part ref DDB101 which replaces Lucas 54412472 and also Lucas 422905. covers applicationsAustin A30, A35, Mini, A40, A50, 10/15cwt, Austin Healey Sprite, Ford 105E, Ford Classic & Classic Capri, MG Midget, MGA, Morris Minor, 1000, Mini, Oxford, cowley, Riley 1.5, riley Elf, Wolseley 1500, 15/50, 15/60, hornet, BMC models, Rootes Husky, Imp, reliant Rebel etc. for years 1955 through to approx 1970 (please verify actual model application to year)
flat side, 4 cylinder. as Lucas part 418888, application Austin A70, Taxi , 25cwt van 1948-53. Bedford light vans 1939-52. MG TC, TD, TF & 1 .1/4 litre 1946-55. Morgan 4/4 Mk 11 1956-59. Morris light vans 194-53. Riley 1.5 and 2.5 litre 1940-55. Singer 1946-57. Vauxhall 4 cyl 1940-52.
100E (1961-62) side exit with round base,Austin Mini(1962/69),Austin A40(1961/67),Austin 1000(1963/67),Austin 1800(1964/67),Austin A60(1961/66),Austin Minivan(1962/69),Austin A35,A55(1962/66),Austin 1 
Lucas reference 400051 or 405468 - fitted to wide range of vehicles through to approx 1973. 
flasher unit - three Lucar terminals , 
700 headlamp unit for pre-focus type bulb. please note that this part is marked for right hand drive. the actual bulb fitted can govern the dip pattern. 
700 headlamp unit for pre-focus type bulb. with pilot hole for side lamp . please note that this part is marked for right hand drive. the actual bulb fitted can govern the dip pattern. 
screw in terminal connection to top 
12 volt ignition coil with push in top terminal 
6 volt ignition coil with acorn nut connection for the high tension lead, twin lucar terminals, supplied with mounting bracket. 
6 volt ignition coil, push in terminal connection top top 
12 volt sport coil, offered with push in HT wire connection only 
electrical temperature sender sensor unit, lucar terminal. thread approx 3/8" (10mm) outside. used 105E engine. 
we are able to supply a wide range of wiring looms for many 1930's and later British vehicles, Austin, Morris, Ford, MG, Jaguar, Alvis etc. these are made to the original specification either cotton auto bulb
6 volt double contact BA15d 36/36 watt double filament bulb. dimensions 35mm wide x 56mm tall with 15mm dia cap. use headlight. discount on price for pack of 10 pieces.
12 volt double contact BA15d 36/36 watt double filament bulb. dimensions 35mm wide x 56mm tall with 15mm dia cap. use headlight. discount on price for pack of 10 pieces. 
12 volt single contact BA15s 36 watt. use headlamp or spotlamp. dimensions 35mm wide x 56mm tall with 15mm dia cap. discount on price for pack of 10 pieces. 
6 volt single contact BA15s 5 watt. dimensions 18.5mm wide x 32mm tall with 15mm dia cap, use side, rear, dash etc. discount on price for pack of 10 pieces. 
6 volt double contact BA15d 5 watt. dimensions 18.5mm wide x 32mm tall with 15mm dia cap, use rear, side or dash etc. discount on price for pack of 10 pieces. 
12 volt single contact BA15s 5 watt. dimensions 18.5mm wide x 32mm tall with 15mm dia cap, Ford ref 100E-13466-A . use dash, side, rear etc. discount on price for pack of 10 pieces. 
12 volt double contact BA15d 5 watt. dimensions 18.5mm wide x 32mm tall with 15mm dia cap, use side, rear, dash etc. discount on price for pack of 10 pieces. 
12 volt single contact BA9s 4 watt. dimensions 9mm wide x 26mm tall with 9mm dia cap, use side or dash. discount on price for pack of 10 pieces.
6 volt single contact SCC BA15s 10 watt. dimensions 18.5mm wide x 32mm tall with 15mm dia cap, use rear or side. discount on price for pack of 10 pieces.
12 volt single contact SCC BA15s 10 watt. dimensions 18.5mm wide x 32mm tall with 15mm dia cap, use side or rear. discount on price for pack of 10 pieces. 
6 volt festoon bulb 11mm x 39mm 5 watt. use indicator or interior. discount on price for pack of 10 pieces. 
6 volt 3 watt festoon bulb 7.5mm x 35mm, use indicator. discount on price for pack of 10 pieces. 
12 volt 3 watt festoon bulb 7.5mm x 35mm, use indicator. discount on price for pack of 10 pieces. 
12 volt double contact BA15d 48 watt single filament. dimensions 35mm wide x 56mm tall with 15mm dia cap. use head or spotlamp. discount on price for pack of 10 pieces. 
6 volt single contact BA9 2 watt. dimensions 9mm wide x 26mm tall with 9mm dia cap, use dash etc. discount on price for pack of 10 pieces. 
12 volt single contact BA9 2 watt. dimensions 9mm wide x 26mm tall with 9mm dia cap, use dash etc. discount on price for pack of 10 pieces. 
6 volt single contact BA9 4 watt. dimensions 9mm wide x 26mm tall with 9mm dia cap, use side light. discount on price for pack of 10 pieces.
6 volt SCC single contact BA15s 15 watt. dimensions 18.5mm wide x 32mm tall with 15mm dia cap, use stop etc. discount on price for pack of 10 pieces.
12 volt SCC single contact BA15s 15 watt. dimensions 18.5mm wide x 32mm tall with 15mm dia cap, use stop etc. discount on price for pack of 10 pieces. 
6 volt single contact BA15s 21 watt. dimensions 24mm wide x 48mm tall with 15mm dia cap, use brake & indicator. discount on price for pack of 10 pieces. 
6 volt double contact SBC BA15d 21 watt. dimensions 24mm wide x 48mm tall with 15mm dia cap, use side, rear, dash etc. discount on price for pack of 10 pieces.
12 volt double contact, BA15d base (equal pins), 21/5 watt double filament bulb. dimensions 18mm wide x 35mm tall with 15mm dia cap, use side/indicator, rear/indicator. discount on price for pack o
6 volt double contact BA15d, 21/5 watt double filament bulb. dimensions 18mm wide x 35mm tall with 15mm dia cap, use side/indicator, rear/indicator. discount on price for pack of 10 pieces.
12 volt double contact BA15d 21 watt. dimensions 24mm wide x 48mm tall with 15mm dia cap, use stop or flash. discount on price for pack of 10 pieces. 
6 volt double contact BA15d, 32 watt single filament bulb. dimensions 24mm wide x 48mm tall with 15mm dia cap, use head or spot. discount on price for pack of 10 pieces. 
12 volt double contact BAY15d offset pins 5/21 watt. dimensions 24mm wide x 48mm tall with 15mm dia cap, use side/stop/flasher. Ford part 100E-13465-B . discount on price for pack of 10 pieces. 
12 volt double contact BA15d equal pin 5/21 watt. dimensions 24mm wide x 48mm tall with 15mm dia cap, use side/stop/flasher. discount on price for pack of 10 pieces. 
12 volt single contact BA15s 21 watt. dimensions 24mm wide x 48mm tall with 15mm dia cap, use stop or flash. discount on price for pack of 10 pieces. 
6 volt double contact BA15d equal pin 18/5 watt. dimensions 24mm wide x 48mm tall with 15mm dia cap, use side/stop/flash. discount on price for pack of 10 pieces. 
6 volt double contact BAY15d offset pin 5/21 watt. dimensions 24mm wide x 48mm tall with 15mm dia cap, use side/stop/flash. discount on price for pack of 10 pieces.
12 volt double contact BA15d 36 watt. dimensions 35mm wide x 56mm tall with 15mm dia cap. use head or spotlamp. discount on price for pack of 10 pieces.
6 volt double contact BA15d, 24/24 watt double filament bulb. dimensions 35mm wide x 56mm tall with 15mm dia cap. use headlight. discount on price for pack of 10 pieces.
6 volt single contact BA15s 36 watt. dimensions 35mm wide x 56mm tall with 15mm dia cap. use spot or headlight. discount on price for pack of 10 pieces. 
12 volt miniature screw MCC (BA9) 2.2 watt. dimensions 10mm wide x 22mm tall with 9mm dia cap, use panel/ignition. discount on price for pack of 10 pieces. 
6 volt miniature screw MCC (BA9) 2.2 watt. dimensions 10mm wide x 22mm tall with 9mm dia cap, use panel/ignition. discount on price for pack of 10 pieces. 
12 volt festoon bulb 18 watt, 15mm x 44mm. used as indicator bulb. discount on 10 pieces 
12 volt 45 watt / 45 watt APF (American Pre Focus) base bulb, dimensions 33mm wide x 53mm tall with 15mm dia cap mounted in 30mm dia flange,
6 volt 35 watt / 35 watt APF (American Pre Focus) base bulb, dimensions 33mm wide x 53mm tall with 15mm dia cap mounted in 30mm dia flange, 
Bosch type 6 volt double contact BA20d, 24/24 watt double filament bulb. dimensions 34mm wide x 64mm tall with 20mm dia cap, use headlight. discount on price for pack of 10 pieces.
Bosch type, 12 volt double contact BA20d, 45/40 watt double filament bulb. dimensions 34mm wide x 64mm tall with 20mm dia cap, use headlight. discount on price for pack of 10 pieces. 
Marchall type, 12 volt single contact BA21s three pin base, 45 watt single filament bulb. dimensions 39mm wide x 58mm tall with 20mm cap, use head or spot lamp. discount on price for pack of 10 pieces 
Marchall type, 12 volt double contact BA21d three pin base, 45/40 watt double filament bulb. dimensions 39mm wide x 58mm tall with 20mm cap, use headlight. discount on price for pack of 10 pieces.
Marchall type, 6 volt double contact BA21d three pin base, 45/40 watt double filament bulb. dimensions 39mm wide x 58mm tall with 20mm cap, use headlight. discount on price for pack of 10 pieces.
Marchall type, 6 volt double contact BA21d three pin base, 30/30 watt double filament bulb. dimensions 39mm wide x 58mm tall with 20mm cap, use headlight. 
Prefocus type 12 volt double contact P22d, 50/40 watt double filament bulb, dimensions 27mm wide x 58mm tall with 20mm dia cap mounted on a 35mm flange, Ford part ref 204E-13007-A. use headlight. disc 
prefocus type 12 volt single contact P22s, 48 watt single filament. dimensions 27mm wide x 58mm tall with 20mm dia cap mounted on a 35mm flange, use spot lamp. discount on price for pack of 10 pieces
Prefocus type 6 volt double contact P22d, 30/24 watt double filament bulb. dimensions 27mm wide x 58mm tall with 20mm dia cap mounted on a 35mm flange, discount on price for pack of 10 pieces.
12 volt 21 watt festoon bulb 15mm x 44mm, use indicator. discount on price for pack of 10 pieces
6 volt 21 watt festoon bulb 15mm x 44mm, use indicator. discount on price for pack of 10 pieces cable
cable - armoured
we manufacture this product - metric spec: 28/0.30mm, imperial spec: 28.012, triple, capacity 16 amps, round profile 9.20mm diameter, option of aluminium or brass bound outer. 
we manufacture this product - metric spec: 28/0.30mm, imperial spec: 28.012, single, capacity 16amp, round profile 3.9mm diameter, option of aluminium or brass bound outer. we offer a price discount on full 30 metre rolls
we manufacture this product - metric spec: 28/0.30mm, imperial spec: 28.012, twin, capacity 16amp, flat profile dimensions 8.70mm x 6.10mm, option of aluminium or brass bound outer. we offer a price discount on full 30 metre rolls
we manufacture this product - metric spec: 44/0.30mm, imperial spec: 44.012, single, capacity 27amp, round profile 4.8mm diameter, option of aluminium or brass bound outer. we offer a price discount on full 30 metre rolls
we manufacture this product - metric spec: 44/0.30mm, imperial spec: 44.012, twin, capacity 27 amp, flat profile dimensions 11.20mm x 7.80mm, option of aluminium or brass bound outer. 
we manufacture this product - metric spec: 14/0.30mm, imperial spec: 14.012, triple, capacity 8amp, round profile 8.30mm diameter, option of aluminium or brass bound outer. we offer a price discount on full 30 metre rolls
we manufacture on this product - metric spec: 14/0.30mm, imperial spec: 14.012, 4 core, capacity 8 amp, round profile 9.20mm diameter, aluminium bound outer. 
we manufacture this product - metric spec: 14/0.30mm imperial spec: 14.012 single capacity 8amp, round profile 3.6mm diameter. option of aluminium or brass bound outer. we offer a price discount on full 30 metre rolls
we manufacture this product - metric spec: 14/0.30mm, imperial spec: 14.012 twin capacity 8amp, round profile 8.0mm diameter, option of aluminium or brass bound outer. we offer a price discount on full 30 metre rolls
cable - battery
armoured cable, 37/0.90mm or 37/.036" battery cable 160 amp capacity, round profile 10.50mm diameter, we offer option of aluminium or brass bound outer which is double the price. 
37/0.90 160 ampere black plastic/pvc battery cable.
flat tinned copper braid cable with clear PVC insulation which can be removed if required. 
black cotton braid battery cable, low lacquer finish, 160 amp capacity, 10.75mm diameter, 
round braided earthing cable (tinned copper) 260 ampere. NOT insulated cable - cotton braid
cotton braid cable, low lacquer finish on black cotton braid. current capacity of 16 amp (old specification 28/0.30mm) approx dimensions 8mm x 5.3mm 30 metre roll lengths are offered at a reduced price
cotton braid cable, low lacquer finish on black cotton braid. current capacity of 8 amp (old specification 14/0.30mm) approx dimensions 7mm x 4.5mm. 30 metre roll lengths are offered at a reduced price
cotton braid single cable low laquer, 28/0.30mm cable, (2.0 mm sq) 16 amp capacity. stocked in a wide choice of colours, from basic plain colours red, black, blue, green, brown, purple, white and yell 
30 metre roll of high gloss lacquer cotton braid Ripaults cable, 44/0.012 cable or equivalent cable, 27 ampere capacity. offered in plain red or green colour only. the price is discounted against purc
cotton braid single cable low laquer, 44/0.30mm cable, (3.0mm sq), 27 amp capacity. stocked in a wide choice of basic plain colours red, black, blue, green, brown, purple, white and yellow etc to incl
cotton braid single cable low laquer, 65/0.30mm cable, (4.5mm sq), 35 amp capacity. stocked in a limited choice of colours red, black, brown, brown with white trace, yellow and yellow with black trace
cotton braid single cable low laquer, 84/0.30mm cable, (6.0mm sq), 45amp capacity. offered to special order ONLY. minimum 10 metre making quantity of any colour choice. 
30 metre roll of high gloss lacquer cotton braid Ripgloss cable, 120/0.012 cable or equivalent cable, 60 ampere capacity. offered in plain red or black colour only. the price is discounted against pur
cotton braid single cable, low laquer, 14/0.30mm cable, (1.0mm sq),8 amp capacity. stocked in a wide choice of colours, from basic plain colours red, black, blue, green, brown, purple, white and yello 
30 metre roll of low lacquer cotton braid cable, 14/0.012 cable or equivalent cable, 8 ampere capacity.offered in following colours - red with blue trace or yellow with red trace. the price is disco
cotton braid single cable, high gloss, 120/0.30mm cable, 60 amp capacity. offered in plain black or plain red ONLY. 
cotton braid outer 4 core cable for passing up the middle of steer column when switch is at top. 3 off 8 amp capacity + 1 off 16 amp capacity. outer diameter 6mm maximum. ignition - cable
HT lead looks very similar to the original rubber covered lead, but it is covered with a soft matt plastic which will withstand oil/heat etc. better than the bright plastic type. copper wire centre.
cotton braided HT lead with copper wire centre, red with yellow trace, red with black trace, yellow with black trace, yellow with green trace, yellow with red trace or plain black, 6.70mm diameter. full 50 metre rolls available with approx 15% discount to price shown.
ignition - terminals
reproduction of a early spark plug cap/termnal marked BIANCHI - although originally known to have been fitted to Lancia and most possibly to other edwardian vehicles. beautifully made and offered with 
CHAMPION WC300 spark plug terminal, 90 degree angle (side entry) cable which has a wire clip to push into the end of the ignition wire. colour red. please note this part is not suppressed (supplied
CHAMPION WCX600 spark plug terminals, embossed CHAMPION, 90 degree angle (side entry) cable which screws on to ignition wire, black. 
knurled spark plug terminal nut - for most modern plugs. 
spilt brass washer for distibutor HT lead each. 
brass solder type HT plug end terminal, wire passes through centre. for standard 7mm HT lead with copper wire centre. 
Wire clip for old style brass spade HT terminal on to spark plug. 
straight spark plug HT cap, black phenolic moulding with carbon suppressor, overall length 58mm. junction and fuse box
single fuse box, black bakelite cover, takes cartridge type fuses 54mm x 32mmhigh. (shown with cover removed) we have a limited stock of new old part of original Lucas manufacture (as opposed to the remanufactured items) which we offer as an alternative at a higher cost of £18.00
small two way fuse box with a screw down nurled nut on the top. base measure approx 45mm x 30mm. black 
fuse box, black finish, accepts 4 modern type Bosch cartridge fuse (available most garages). 28mm high clip on lid, 61mm x 44mm. 
fuse box, black finish, accepts 6 modern type Bosch cartridge fuse (available most garages). 28mm high screw on lid - 90mm x 44mm. 
small two way fuse box with a screw down nurled nut on the top. base measure approx 119mm x 45mm. black
round 2 terminal bakelite junction box with screw cover, 1 1/2" (38mm) diameter. Lucas part 78265. (lower cover removed). original new old stock. 
round 4 terminal bakelite junction box with screw cover, 2" (51mm) diameter. equivalent to Lucas part 76264. (lower shows cover removed). spare cover see 309A we have a limited stock of new old part of original Lucas manufacture (as opposed to the remanufactured items) which we offer as an alternative at a higher cost of £16.00 each
round 6 terminal bakelite junction box with screw cover, 2 3/8" (60mm) diameter. equivalent to Lucas part 76266. (lower shown cover removed) we have a limited stock of new old part of original Lucas manufacture (as opposed to the remanufactured items) which we offer as an alternative at a higher cost of £16.00 each
Lucas SF4, 4 fuse box, base 73mm x 72mm x approx 60mm overall height. centre screw to lid top, black bakelite. supplied without fuses. regulator & cut-out
12 volt reproduction unit, base 115mm x 87mm x approx 95mm overall height. 9 screw terminals.
6 volt reproduction unit, base 115mm x 87mm x approx 95mm overall height. 9 screw terminals. 
12 volt electrical relay used where brake and indicator rear lights are used on the one bulb. application, MG, Morris Minor etcsize approx
12 volt unit, 5 screw terminals. size approx 85mm x 80mm x 95mm tall. 
12 volt unit with Lucar push-on terminals, size approx 85mm x 80mm x 95mm tall. black. 2 bobbin type
6 volt unit, 5 screw terminals, 2 bobbin, size approx 85mm x 80mm x 95mm tall. 
Lucas RB340 type, three bobbin, 22 amp. sleeving
useful for tidying up old looms
yellow with black fleck cable sheath, offered in two sizes 5mm or 8mm. per 1000mm length only.
galvanised steel flexible metal conduit used for sheathing cables to lamps etc. outer diameter approx 3mm larger than inner. supplied in lengths cut off roll. inside (bore) size specified.
plated flexible metal conduit used for sheathing cables to lamps etc. supplied in 1500mm long lengths only, chromium or nickel plate on brass. outer diameter approx 3mm larger than inner.bore (insid
stainless steel flexible metal conduit used for sheathing cables to lamps etc. we only offer the one size of 8mm bore, outer diameter approx 3mm larger than inner. supplied in length cut off roll.
non adhesive PVC harness tape for rebinding wire harness offered in black and grey. roll 20m x 19mm wide 
bituminised fabric semi rigid wire harness sleeve, black. offered in different sizes. please note that bore sizes are nominal.
black PVC cable sleeving, 0.5mm wall thickness, in 25 metre rolls only.offered on bore sizes 5mm, 7mm, 9mm and 11mm
switch - battery isolator
battery isolating switch with flange for panel fixing and black know marked Off with arrow. requires 19.5mm hole and two 4mm fixing holes. two 8mm electrical cable connection studs to rear. 
sturdy panel mounted battery master switch, similar to Lucas SSB106 model.requires 19mm hole in panel. well made reproduction part
battery master mwitch, cheaper alternative, black plastic body, red removable plastic key. usually mounted in earth lead. 
battery master switch for dashboard mounting etc., mounting flange. knob can be detached for installation by removal of rear circlip. usually mounted into earth lead. 
simple yet effective battery master switch- fits on the battery post - no modifications needed -screw knob detaches if required. switch - brake
brake light switch, terminals protected by a rubber cover, connects to linkage with a spring 
Lucas pattern 51C 'pull on' brake switch, metal body 63mm wide, screw terminals on top. Ford part reference Y-13480 
brake light switch which connects to linkage with a spring. electrical contacts 'break' on pull. no rubber cover . 
bakelite body, lever action. fits to RHD cars/5cwt van & LHD E83W 
bakelite body, lever action. suits RHD E83W and LHD cars/5cwt van switch - dashboard
aluminium body with black push button, two terminals for wood dash. this button is very similar to the vintage Bosch model but has a clip-on cover in place of the early threaded variety. 1 3/8'' (35mm 
surface mount Lucas type SPB140 switch (model HD77). base 50mm diameter, two bolt mounting through back (35mm hole centres). side dip switch (lever 18mm long), front horn push (button diameter 25mm). 
ignition switch - panel mount with two keys. requires 19mm dia, hole. - 4 key positions - accessory/off/ignition/start. 
ignition switch - panel mount with two keys. requires 19mm dia, hole. - 2 key position, off/on positions only. 
PLC5 type combined key on/off and off/side/head lamp switch. approx 56mm diameter (requires 53mm hole in metal dash panel). the off/side/head positions are printed on the black face panel. screw termi 
PLC6 type combined key on/off and off/side/head lamp switch. approx 56mm diameter (requires 53mm hole in metal dash panel). the off/side/head positions are displayed on a white background through a cu 
switch as Lucas PPG1 style light switch with pull/twist/pull action. fits through 10mm hole max panel thickness 3mm with chrome retaining nut, hexagon shaft with spring loaded locating pin, three scr 
pull on / push off switch (Lucas SPB104). long shank (18mm long, 9mm diameter,) suitable for wooden dash. black plastic knob on hexagonal stem. knob removed by depressing spring loaded pin, two brass 
pull on / push off switch, long threaded shank (16mm long, 9mm diameter,) suitable for mounting through wooden dash. overall length 73mm, maximum diameter 18mm, requires 9.5mm panel hole. grub screw 
push button (spring loaded) black knob, 22mm diameter chromium bezel, long type for wooden dash, maximum dash thickness 20mm. (requires 19mm hole). makes contact when pushed. as Lucas 31363 SPB106 we have a limited stock of new old part of original Lucas manufacture (as opposed to the remanufactured items) which we offer as an alternative at a higher cost of £20.00 each
push button (spring loaded) black knob, 22mm diameter chrome bezel, short type for metal dash, maximum dash thickness 7mm. (requires 19mm hole). makes contact when pushed. as Lucas 31967 type SS5. we 
push button, flange for mounting on to dash, button head approx 38mm dia. mounting flange 53mm x 35mm with two screw hole (hole centres 42mm). Lucas type SPB160 replacement item 
pull/push switch, long shank suitable for wooden dash, maximum dash thickness 10mm, fits 8mm hole, overall dimensions 58mm long x 30mm at widest point, two brass terminals with screws, black knob 
useful rotary 3 position (off, side, head) switch with black lever to fit a metal dash (26mm hole) with fixing nut to retain. 4 screw terminals to rear. 
surface mounted dip switch, 2 5/8'' (67mm) diameter, three hole fixing. well finished in black plastic. new old stock Lucas part 31001. 
toggle switch, on/off only, requires hole through metal panel 13mm. nickel plate toggle lever 
a neat little toggle switch with a LED in the end of the toggle that lights up when power is turned on. panel hole 13mm, specify colour choice please, rated at 15amp.
rotary on-off turn switch with black knob with two flattened grips. short shank for metal dash, requires 19mm panel hole, bezel 22mm diameter. choice of black bezel or at extra cost chrome bezel . as switch - dip
floor mounted traditional dip switch for foot use, equivalent to Lucas model FS22-1, base plate measures 75mm x 40mm with 60mm hole centre fixing screws, three terminals with screw/plate connections, 
foot operated dip switch for mounting through floor. base measures 55mm. fixing holes 38mm. switch - indicator
panel mount indicator switch, suitable for any application. requires 25mm hole through metal panel. please note that this part does NOT self cancell
steer column mount indicator/trafficator switch. secures to round steer column using metal band clip. base measures 30mm deep (front to back), black bakelite type finish with plated stalk. overall len please note that this part does NOT self cancel
indicator switch which mounts to steering column, secured with a band clip thus can be removed without leaving any extra holes etc. body approx 56mm tall x 44mm deep, overall length approx 164mmplea
panel mount indicator switch, with knob which illuminates in use, 12 volt application only. requires 25mm hole through metal panel for mounting. please note that this part does NOT self cancell
steer column mount indicator/trafficator switch. secures to round steer column using metal band clip. base measures 30mm deep (front to back), black bakelite type finish with plated stalk, overall len 
clockwork panel mounted indicator switch (suitable for 6, 12 or 24 volt systems), make and break contacts for approx 20-25 seconds then self cancels. body size approx 45mm x 55mm x 25mm. requires 12mm 
surface mount traficator switch without warning lamp. switch - start
Lucas SRB312 floor mounting starter button, heavy pattern for connecting into starter/battery cables. part reference 54033241. supplied with push button knob and flange plate. body measures 49mm diame 
12 volt remote starter button that you can mount under the bonnet for that ease of starting the engine whilst you're working on the car. 
floor mount starter switch for connecting directly into starter/battery cables, four mounting holes, two 5/16" terminals studs with nuts, as Lucas model ST18 
bulkhead fitting pull type starter switch (945), Lucas modet type ST19-2, applicable for 6 or 12 volt application, terminals for heavy cables. 
starter switch which attaches to the motor case, Lucas model type ST9, applicable for 6 or 12 volt applications. Ford part reference BE-11450 
as Lucas ST10 style start switch. cable operated, mounts on end of starter. switch - sundry
interior light switch with stainless steel cover. slides on/off, suitable for door pillar application.cover approx 27mm x 51mm, holes 35mm.
fits through 8mm hole in panel 
small round surface mount toggle on/off switch, 28mm diameter x approx 13mm tall cover. nickel/chrome plated cover (unscrews to get to terminals). only suitable for 6 volt or 12 volt, maximum rating 3 
black plastic type toggle switch, requires 12mm panel hole. on/off only 
interior light toggle switch, chrome finish, cover plate 43mm x 30mm with bevel edges.on/off only
please note that the connection terminals will require wires to be soldered in place.
terminals and parts
solderless battery terminal, round post, state whether positive or negative required. 
solder type end fixing terminal for usual 160amp battery lead/cable 
brass P clip for general purpose uses. available in the following diameter sizes and pack quantities.552A - 4.5mm per packet 25 pieces (3.2mm fixing hole)
552B - 6mm per packet 25 pieces
chassis clip, simply push on to the edge of the chassis to hold cables/pipes, 58mm long, per packet of 10 
two panel mount sockets (red & black) and two equal size pin plug (pins 12.5mm centres, plug pins 3.18mm diameter) , often used for inspection lamps etc. equivalent to Lucas inspection lamp plug 54502 
two, three and four brush dynamo and starter brush sets. 
solder type nipples for snap connector, (note already supplied with parts 558 and 559) per packet of 10 pieces 4.75mm diameter. offered in pack of 10 pieces or pack of 100 pieces 
metal clip (plated) for securing pipe or cable etc. available in the following diameter sizes 5mm, 6mm, 8mm, 10mm and 12mm - per packet 10 pieces
two pin plug with different diameter pins (pins 12.5mm centres, plug pins 3.18mm diameter for black socket, 3.81mm diameter red socket) , often used for inspection lamps etc. equivalent to Lucas plug 
starter-solenoid rubber button cover, equivalent to Lucas prt 760130 
single (joins 2 wires) snap connector, supplied with solder type nipples, per packet 10 pieces complete. 
double (joins 4 wires) snap connector supplied with solder type nipples. per packet of 10 pieces complete. 
two sockets with different diameter pins, often used for inspection lamps etc. equivalent to Lucas sockets 38605A, as supplied by lucas for fitting Lucas plug 304919. will fit our part 960P 
starter-solenoid terminal insulator rubber, equivalent to Lucas part 764272