we offer replacement keys cut for door and ignition switch. these are cut to number only, 2 identical keys supplied. we restrict this to the key series -key sequence numbers MRN1 through 50, FA501 t
aluminium sheet
ribbed aluminium sheet with approx 8 rib per 25mm. sheet size 2000mm x 1000mm with the ribs running the full length of the sheet. thickness 1.2mm. we can offer either full sheet or half sheet 2000mm
aluminium strip
22mm wide across top, flange 19mm x 2mm thick. per 2 metre length.note the angle between flange and under top is 90 degree. measure under face to flange approx 10.4mm and 9.2mm (the flange is set
half round section, 13mm base x 5mm, 2 metre lengths only. can be coiled for despatch if necessary.click on "bigger image" for more detail dimensions
half round section, 16mm wide base x 5mm, 2 metre lengths only. can be coiled for despatch if necessaryclick on "bigger image" for more detail dimensions
half round section, 19mm base x 5mm, 2 metre lengths only. can be coiled for despatch if necessary.click on "bigger image" for more detail dimensions
half round section, 25mm base x 5mm, 2 metre lengths only.click on "bigger image" for more detail dimensions
half round section, 32mm base x 5mm, 2 metre lengths only.click on "bigger image" for more detail dimensions
half round section, 38mm base x 5mm, 2 metre lengths only.click on "bigger image" for more detail dimensions
Tee section equal 16mm wide x 19mm, 2 metre lengths only.click on "bigger image" for more detail dimensions
fluted angle, running board edge 19mm x 19mm, 2 metre lengths only.click on "bigger image" for more detail dimensions
fluted angle, running board edge 23mm x 23mm. 2 metre lengths only. click on "bigger image" for more detail dimensions
fluted angle running board edge 25mm x 25mm, 2 metre lengths only. 
drip moulding 20mm x 9mm, 2 metre lengths only.click on "bigger image" for more detail dimensions
gutter section with fold over flap to cover fixing screws when fitted.16mm x 13mm, available in 7ft (2.15 metre) lengths only
Tee section offset , 16mm wide x 19mm, 2 metre lengths only.click on "bigger image" for more detail dimensions
rounded angle, running board edge. 21mm x 20mm , 2metre lengths onlyclick on "bigger image" for more detail dimensions
cope moulding, 25mm x 10mm. 2 metre lengths only.click on "bigger image" for more detail dimensions
body parts
Moulding Clip/Rivet, for fixing body moulding strips to vehicle side. to fit moulding with approx 11mm gap (clip measurements on larger image) supplied with fixing rivet for 3mm hole. will suit ford 1 
Moulding Clip/Rivet, for fixing body moulding strips to vehicle side. to fit moulding with approx 11mm gap (clip measurements on larger image) supplied with fixing rivet for 3mm hole. will suit ford 1 
Moulding Clip, for fixing body moulding strips to vehicle side. to fit moulding with approx 11mm gap (clip measurements on larger image) supplied with fixing rivet for 3mm hole. will suit ford 100E wi 
Moulding Clip/Rivet, for fixing body moulding strips to vehicle side. to fit moulding with approx 9mm gap (clip measurements on larger image) supplied with fixing rivet for 3mm hole. sold each. 
Moulding Clip/Rivet, for fixing body moulding strips to vehicle side. to fit moulding with approx 8mm gap (clip measurements on larger image) supplied with fixing rivet for 3mm hole. sold each. bonnet catch
pull bonnet catch from a Wilmot Breeden pattern as used as original equipment for Morris 8, Morgan etc. chrome on brass, approx 4.75" / 120mm long. complete with bonnet catch plate. 
small top quality catch, approx 4.25" / 110mm long overall, complete with catch plate, chromium plated on brass, small rubber buffer on back. base plate and catch plate same size (40mm x 19mm with hol 
large top quality catch approx 135mm overall complete with catch plate, chromium plated on brass. mountings approx 90mm apart 
small spring loaded pull catch with loop finger pull ring, painted finish, complete with pocket, approx 118mm long. chrome finger pull ring. hook for pocket approx 80mm from base. 
open spring bonnet catch, nickel plate finish, 125mm long, a cheap spring catch to hold a bonnet down, supplied with top catch. 
bonnet/hood catch supplied with pocket. polished stainless steel parts, 91mm tall overall, base 55mm wide. choice of 2 hole mount (13mm deep) or 3 hole mount (30mm deep). 
bonnet catch plate for mounting to bonnet panel. base approx 72mm tall x 27mm wide. useful top catch fitting to be used as an alternative to several of out bonnet catches which have a clip top
stainless steel bonnet catch with T bar grip pattern. 95mm long, two screw base (mount holes 35mm centres) mounts horizontally. supplied with zinc plated pocket.
chrome plate bonnet catch as fitted to Morris Minor, MG, Wolseley Hornet etc. the catch has a kidney shape plate to allow movement. catch size 133mm overall. 
medium size basic type commercial type bonnet catch. 100mm overall high, supplied with bonnet catch pocket. supplied in primer paint finish only. base to pocket clip approx 90mm. 
chrome finish long tail lever pattern bonnet catch. sold in opposite pair sets only. push top down against spring to engage hook, turn through 90 degree to release. lever top 80mm long, angled two stu 
chrome finish on brass, tee shape twist handle fastener. push top down against spring to engage hook, turn through 90 degree to release. lever top 52mm long, angled base approx 45mm diameter with four 
chrome finish on brass, tee shape twist handle fastener with 'R' embossed into top. push top down against spring to engage hook, turn through 90 degree to release. lever top 52mm long, angled base app 
chrome plate hook shape bonnet fastener with pocket. a traditional shape utility type catch. pocket and base mounting plate is zinc type plate finish. overall size approx 115mm (hook width 60mm). 
bonnet catch pull and locating bracket of 'squashed tube' pattern offered by Ewarts. 113mm long. finger pull is shaped off the end of the tube. base 36mm x 24mm. bonnet clip base 31mm x 22mm. we offer 
rubber hook with zinc plated bracket and clip. overall length approx 122mm. maximum extension from relaxed to tension not to exceed 10%. 
small rubber hook with zinc plated bracket and clip. overall length approx 54mm. maximum extension from relaxed to tension not to exceed 10%. 
screw down bonnet catch which bolts to the outside of the bonnet panel, new manufacture, 4 mounting holes approx approx 28mm and 24mm apart vertically on 48mm round base, chromium top, approx 85mm tal bonnet hinge
heavyweight hinge, 5/16" (8mm) steel pin, 16 swg (1.6mm) unpolished brass flap undrilled, 3" (76mm) across flats when open, 2" (51mm) knuckles. offered in various lengths.
medium weight hinge, 1/4" (6mm) steel pin, 16 swg (1.6mm) unpolished brass, flaps undrilled, 2 1/2" (64mm) across flats when open, 2" (51mm) knuckles, offered in specific lengths. 
folded type of hinge, brass pin, stainless steel flange, 2" (approx 51mm) knuckles, these are supplied in sets of one top hinge and two side hinges OR as individual hinges - top hinge 5/16" (8mm) pin
folded type of hinge, brass pin, stainless steel flange, 2" (approx 51mm) knuckles, these are supplied in sets of one top hinge and two side hinges OR as individual hinges - top hinge 1/4" (6mm) pin 1 
heavyweight stainless folded type top bonnet hinge, 3/8" (10mm) brass pin, 16swg stainless steel flap folded towards pin, approx 45mm when open, 50mm knuckles, 54" (1.37m) long 
chrome on brass fitting. base 45mm x 15mm, mounting holes 31mm apart. 
chrome on brass fitting. base approx 45mm x 16mm, 28mm deep overall. mounting holes 31mm centres. 
chrome on brass fitting base approx 45mm x 16mm, 20mm deep overall. mounting holes 31mm centres.
heavy bonnet hinge 3/8"/10mm diameter pin, 16 swg (1.6mm) flaps , 75mm across flaps when open, 51mm knuckles 5ft/ 1.52m long only. offered in brass flaps with stainless pin OR stainless flaps with bra 
chrome plate on brass fitting with 1/4" (approx 6mm) hole. base 45mm x 15mm, mounting holes 31mm apart. 
chrome plate on brass fitting with 1/4" (approx 6mm) hole. base 45mm x 15mm, mounting holes 31mm apart. 
chrome on brass folded centre bonnet strip. 1270mm length (50") 21mm wide. side panels are folded and slide in place. 
chrome plate end cover and clamp for centre strip. base 51mm x 13mm, holes 35mm apart. 
folded steel side strip for sliding into bonnet strip, 48"/1.22 metre long. weld to flat panel. 25mm overall width (flange 14mm) bonnet rest tape
copper bifurcated rivet, 7.5mm head, stem 3.8mm x 11mm. for fixing bonnet tape etc. per packet 10
19mm wide x approx 4.5mm thick. this product is impregnated to produce a dark brown stiff beading (as original product) which will acts as the rubbing tape between bonnet (hood) and radiator cowl and we offer a discount on full 30 metre roll
19mm wide x approx 3mm thick. this product is impregnated to produce a dark brown stiff beading (as original product) which will acts as the rubbing tape between bonnet (hood) and radiator cowl and bo we offer a discount on full 30 metre roll
16mm wide x approx 4.5mm thick. this product is impregnated to produce a dark brown stiff beading (as original product) which will acts as the rubbing tape between bonnet (hood) and radiator cowl and we offer a discount on full 30 metre roll
25mm wide x approx 4.5mm thick. this product is impregnated to produce a dark brown stiff beading (as original product) which will acts as the rubbing tape between bonnet (hood) and radiator cowl and we offer a discount on full 30 metre roll
13mm wide x approx 4.5mm thick. this product is impregnated to produce a dark brown stiff beading (as original product) which will acts as the rubbing tape between bonnet (hood) and radiator cowl and we offer a discount on full 30 metre roll
13mm wide x approx 3mm thick. this product is impregnated to produce a dark brown stiff beading (as original product) which will acts as the rubbing tape between bonnet (hood) and radiator cowl and bo we offer a discount on full 30 metre roll
25mm wide x approx 3mm thick. this product is impregnated to produce a dark brown stiff beading (as original product) which will acts as the rubbing tape between bonnet (hood) and radiator cowl and bo we offer a discount on full 30 metre roll
10mm wide x approx 3mm thick. this product is impregnated to produce a dark brown stiff beading (as original product) which will acts as the rubbing tape between bonnet (hood) and radiator cowl and bo we offer a discount on full 30 metre roll
16mm wide x approx 3mm thick. this product is impregnated to produce a dark brown stiff beading (as original product) which will acts as the rubbing tape between bonnet (hood) and radiator cowl and bo we offer a discount on full 30 metre roll
32mm wide x approx 3mm thick. this product is impregnated to produce a dark brown stiff beading (as original product) which will acts as the rubbing tape between bonnet (hood) and radiator cowl and bo we offer a discount on full 30 metre roll
natural coloured 19mm wide x approx 4.5mm thick beaded webbing tape which will acts as a soft rubbing tape between bonnet (hood) and radiator cowl and body scuttle. note this is NOT proofed and NOT co brass & nickel strip
25mm x 25mm (1" x 1") right angle channel, thickness 1.5mm (1/16"). offered in 1800mm lengths. 
fluted angle solid nickel running board edging. measures 21mm across by 23mm down the side with 4 ribs on top. this item is a rolled section as used in the edwardian and early vintage period. lengths brass channel
H section brass windscreen extrusion, approx 13mm wide, 24mm high, groove approx 8.5mm. cut in 10cm units. price shown per metre.Click on "bigger Image" for complete dimensions
we can supply this material in cut lengths from 100mm length to a maximum of 2000mm length as shown in length option box.
U section brass windscreen extrusion, approx 12.5mm wide, 19mm high, groove approx 9mm. cut in 10cm units. price shown per metre.Click on "bigger Image" for complete dimensions
we can supply this material in cut lengths from 100mm length to a maximum of 2000mm length as shown in length option box.
H section brass windscreen extrusion, approx 14mm wide, 25mm high, groove approx 9.5mm. cut at 10cm units. price shown per metreClick on "bigger Image" for complete dimensions
we can supply this material in cut lengths from 100mm length to a maximum of 2000mm length as shown in length option box.
h section brass windscreen extrusion, approx 15mm wide, 33mm high, (upstand measures 16mm from flat) ,groove approx 9.5mm. cut in 10cm units. price shown per metre.Click on "bigger Image" for com
we can supply this material in cut lengths from 100mm length to a maximum of 2000mm length as shown in length option box.
U section brass windscreen extrusion, approx 13mm wide, 18mm high, groove approx 10mm straight sides with small radius to bottom corners. cut at 25cm units. price shown per metre. offer in the unit le 
U section brass windscreen extrusion, approx 13mm wide, 19mm high, groove approx 7.7mm straight sides with small radius to bottom corners. cut in 100mm units. this section has a 2.45mm thickness wall catches
small over-centre catch suitable for right angle fitting (ie toolbox lid), base drop 60mm from angle x 32mm wide, chrome on brass. 
angled mounting catch ideal for tool box etc. chrome on brass. can be locked with small padlock (not supplied). base 63mm x 30mm, overall 83mm.base has 4 mounting holes and top bracket has 2 mountin
Dzus type 40 fastener for panel fixing with easy removal. 16mm dia slotted countersunk head on panel fixing plate 38mm x 22mm, cadmium plated. 1/4 turn to lock on to wire spring (supplied). panel moun 
small swivel catch for panels etc, chrome finish, approx 50mm x 45mm. lever locates at 90 degree positions to backplate. 
larger swivel catch for panels etc, chrome finish, approx 50mm x 65mm. lever locates at 90 degree positions to backplate.
fitted to top hood rail, to locate on to 16mm diameter peg on windscreen frame. chrome on brass. base 63mm x 13mm. 
set of two castings (male and female) approx 43mm long x 17mm wide, self colour brass. for aligning and positioning hood stays when frame is lowered. 
small over-centre catch, base 65mm x 32mm, overall 80mm, chrome on brass.six mount holes - 23mm centre horizontal, 35mm centre vertical. the single furthest holes measure 50mm apart.
small over-centre catch, base 70mm x 32mm, overall 80mm, shaped top, chrome on brass. 
medium over centre catch, base 77mm x 26mm, 105mm overall, chrome on brass.six mount holes on base - horizontal 15mm centres, 52mm vertical centres and the middle holes are 69mm centres approx.
small safety throw over type catch, base size approx 67mm x 22mm (supplied handed) chrome on brass. 
chrome on brass. can be locked with small padlock (not supplied). base 75mm x 30mm, overall 93mm.base has 4 mounting holes and top bracket has 2 mounting holes.
small throw over type safety catch, base size approx 45mm x 28mm (supplied handed) chrome on brass. approx 31mm horizontal hole centres when fitted. 
plated brass clamp for securing Pytchley sliding roofs. approx 62mm diameter, supplied with leather pressure pad, clamp washer and tightening knob. 
large throw over type safety catch, base size approx 65mm x 52mm (supplied handed), chrome on brass. 
attractive chrome on brass throw over safety catch - ideal for the veteran vehicle. supplied in pairs only (one piece left hand, one piece right hand). base 41mm x 51mm with two screw mounting holes i 
windscreen silencer, swivel base 38mm x 12mm, knurled knob, chromium finish 
catch plate for windscreen silencer, choice of straight or angled. chrome plate, 22mm wide. check strap
black or brown stitched leather strap, 200mm x 51mm, with staples in either end. 
brown or black stitched leather strap, 200mm x 51mm, with chrome fittings. choice of fixed end (type A) or sliding end (type B) 
sliding metal door retaining check with rubber end buffer. angle can be adjusted by customer. overall length 125mm. 
black or brown stitched leather door check strap 30mm wide. the staples (footman loops) are fitted at each end. 
sliding type as fitted to many vehicles. spring steel centre covered with leather. 240mm long x 38mm wide. choice of black or brown leather colour door locks
remote action cast brass door lock complete with lever mechanism, lock 83mm x 89mm brass finish. overall length of lock to lever (handle mounting) 340mm.use striker plates 541 or 542
surface fitting door lock, 80mm x 60mm x 15mm deep, plated finish. 
surface fitting door lock, with a lever handle similar to pre-war shape. base size approx 87mm x 51mm with a long tongue, particularly suitable for open bodywork, plated finish. square hole for handle 
small chromium plated surface mount door lock with lever to top, of a design common to many 'vintage' locks. base size 86mm x 51mm approx. original early Morgan style. square hole for handle shaft app 
surface fitting lock with top lever action. base 51mm x 86mm zinc plated. with a little handle modification this will modify quite easily to a lock of vintage appearance. square hole for handle shaft 
heavy surface fitting door lock 78mm x 76mm approx with lever to top. body stands 19mm proud of mounting panel. the cast brass body is offered in chrome plated finish only 
surface mount lightweight door lock with stainless steel cover plate. rear pull to open, no provision for shaft of external handle.mounting screws 33mm horizontal, 44.5mm vertical. the lock tongue c
'Silent-travel' lock, as used on MG and other pre-war cars, chrome finish 63mm wide 68mm tall body, chrome cover. facility for shaft of exterior handle to fit into back. use striker plates 602N,602W,6 
cast malleable iron 38mm x 32mm, lock striker click/click 
cast brass 22mm x 54mm striker, click only 
face mounting plate (suit Cobra, Healey) and wedge complete. mounting plate 95mm x 33mm 
narrow mounting plate (early T type) and wedge complete. mounting plate 95mm x 20mm 
wide mounting plate (TD/TF type) complete with wedge. mounting plate 95mm x 34mm 
replacement dovetail wedge and nut only (no mount plate).dimensions, wedge 20mm across (wide end) 11mm across (narrow end) 22mm deep. 5/16 stud 35mm long (18mm threaded). door wedge
door silencer. we have re-manufactured this quality silencer of the type refered to as Bedford or Beatonsons pattern. chrome plated brass supplied in two parts. an essential fitting for the heavier do 
rubber door buffer complete with plated steel shoe and brass eyelet. size approx 32mm x 12mm. 
dovetail door wedge. size 76mm x 43mm approx. metal and rubber buffer which is positive in action. supplied in two part set. 
brass and iron cast dovetail wedge, 22mm x 52mm approx. both halves tapered to join in very positive action. general
Heavy dished, plated steel washer 22mm dia with 8mm hole, used when screwing floor boards in place 
black enamel finish on steel check strap staple, in strap widths of :32mm strap, approx 58mm hole centres
38mm strap, approx 62mm hole centres
51mm strap, approx 80mm hole centres
chrome finish on brass check strap staple, in strap widths of :32mm strap, approx 58mm hole centres
38mm strap, approx 62mm hole centres
51mm strap, approx 80mm hole centres
ivory coloured knob for rear blind pull. approx 19mm diameter with hole for cord through centre.
ivory coloured hook for rear blind pull rope, with fixed wood screw, approx 16mm diam. general - covers
keyhole escutcheon - flap is hinged at the top and opens up against a spring. 2 hole (21mm centres) fixing in base plate - chromium finish. approx 29mm diam.
keyhole escutcheon - flap is hinged at the top and opens by sliding sideways against a spring. 2 screw fixing showing on outside of the cover. offered chromium or nickel plated finish. 
keyhole escutcheon - brass construction, flap is hinged at the top and opens up. 2 hole (35mm centres) fixing in base plate - available in polished brass,chromium or nickel finish. lid measures appr
saloon drain hole cover for roof, chrome on brass, overall approx 56mm x 35mm 
'fig-leaf' escutcheon cover, chrome, lift up, spring loaded lid. used on TR etc. 2 hole (21mm centres) fixing in base plate. general - locks
budget lock, steel with brass tongue approx 79mm x 22mm. 
mortice budget lock - for side fixing 24mm deep, 88mm long, tongue protrudes approx 10mm. 
"bridge type" budget lock, plated finish. overall height 19mm, 22mm wide x 89mm long, handed left or right 
budget lock 85mm x 22mm in galvanised finish, supplied with keep. this lock is NOT handed and works to left or right.
T key for budget lock, self colour steel. approx length 140mm. 
locking type cubby lock - push button to open, rear of panel fixing. 
locking deluxe type cubby lock, push button to open fixes through 3/4"/19mm hole, chrome bezel. 
compartment lock - suitable for panel or bonnet. chrome bezel, fits through 3/4" (19mm) dia. hole. 
Chrome plated push cubby catch, not lockable 
flat base hook type budget lock. base 112mm x 25mm. select E04A-16658 (right hand) or E04A-16659 (left hand) please. also application MG Midget, Triumph TR4 and TR5 boot latches.
budget lock keep, steel general - studs and bolts
plated dome brass stud to go on to top panel of bonnet to prevent 'chattering' when the two top panels fold on to each other, 16mm diameter, choice of shallow, approx 8mm high or deep 10mm high, chrom 
chromium plated dome head bolt with flats beneath (supplied with washer and nut). choice of round head 14.5mm head diameter x 26mm long x 5/16" (approx 8mm) thread OR flat head 15.7mm head diameter x 
chromium plated round head bolt with flats beneath, 37mm long x 3/8" thread. 
chrome on brass, approx 25mm diameter, shallow dome head 3/8"BSW (approx 10mm) thread, 32mm long. 
oval head, chromium plated bumper bolt, 25mm x 16mm approx. 5/16"BSW (approx 8mm) thread. 
oval head chromium plate bumper bolt, 35mm x 22mm appox. 3/8BSW (approx 10mm) thread. 
mushroom head bolt for securing mudguards/fender to stays. approx 22mm diameter head, stud 32mm long threaded 1/4" BSW (approx 6mm), zinc plated on steel. each or bulk pack of 50 (£36.50). 
large flat head steel wing mounting bolt, head 25mm diameter, thread 5/16"BSW x 38mm under head. 8mm square shank under head. handle
chrome plate trim ring for handle and winder, 46mm diameter, centre hole approx 16mm. 
early pattern handle or winder escutcheon trim ring with three hole fixing. 59mm diameter. offered in chrome or nickel finish 
push on sleeve spacer for handle fitting, 5/16" to 3/8" size. (8mm to 10mm) 
sprinq loaded escutcheon for interior door handles & window winders, chrome, approx 38mm diameter x 17mm high. centre hole approx 16mm. handle - exterior
chrome plate for boot/trunk T boot handle approx 95mm long, round (28mm diameter) escutcheon with two locating tags.
T boot or bonnet locking handle, chrome finish. approx 95mm wide, fitted with round escutcheon plate with male threaded studs 36mm centres. short plain square shaft. original application MG Midget and 
plain T boot handle approx 108mm, escutcheon hole centres 36mm, chrome plated. available locking only. 
chromium plated plain shaped door handle 105mm long.offered with large and small mounting escutcheons, hole centres as indicated.
chromium plated (alternative nickel plate finish also offered) early pattern door handle, 98mm long, escutcheon fixing holes at 36mm centres. 
fine vintage style handle. approx 90mm long, supplied with undrilled escutcheon, polished brass 
torpedo handle. approx 85mm long, supplied with undrilled escutcheon, polished brass. 
chromium finish typical post war curved pattern 132mm.offered with large and small mounting escutcheons, hole centres as indicated.
chromium finish handle 132mm long. fitted with special heart-shaped escutcheon with mounting holes at 36mm centres.(as fitted to MGTF, Morris Series E etc.) 
chromium plated with slight raised rib on face 110mm long.offered with large and small mounting escutcheons, hole centres as indicated.
small handle, as used on cobra etc. 74mm long escutcheon hole centres 35mm chrome finish. 
nicely shaped exterior door handle with slightly hollowed centre area, chromium finish, approx 100mm long. mounting ecsutcheon hole centres approx 36mm centres. shaft length is only 40mm long but can originally Ford model A handle 1928/29 closed car
chrome plate on brass fluted pattern door handle approx 97mm long. fitted with squared escutcheon (57mm x 30mm) hole centres at 42mm approx. original pattern for small Bedford vehicle. offered in lock 
chromium plated swept type door handle, supplied singly to suit left and right of vehicle. 117mm long, escutcheon fixing holes 36mm centres.
locking chrome plated swept type door handle, supplied in pairs only to suit left and right of vehicle. matched key sets. 117mm long, escutcheon fixing holes 36mm centres.
loop carriage handle. approx 90mm wide, supplied with undrilled escutcheon, polished brass only. 
curved top bronze handle, approx 72mm long, supplied with escutcheon. one of the selection of original handles to which we fit a new shaft.Stock Very Limited, 3 piece as shown On
small curved top solid nickel handle, approx 75mm long, supplied with escutcheon. one of the selection of original handles to which we fit a new shaft. limited quantity available only.
small flat top solid nickel handle, approx 75mm long, supplied with escutcheon. one of the selection of original handles to which we fit a new shaft. limited quantity available only. 
curved top brass handle, approx 85mm long, supplied with escutcheon. one of the selection of original handles to which we fit a new shaft.Stock Very Limited, 1 pair (2 handles) O
barrel side flat face solid brass handle, approx 90mm long, supplied with escutcheon fitted. one of the selection of original handles to which we fit a new shaft.Stock Very Limit
brass curved top handle, approx 80mm long, supplied with escutcheon. one of the original handles to which we fit a new shaft.Stock Very Limited, 1 Only Available
curved top solid nickel handle, approx 100mm long, supplied with escutcheon. one of the selection of original handles to which we fit a new shaft.Stock Very Limited, 1 pair (2 ha
barrel side torpedo solid brass handle, approx 97mm long, supplied with escutcheon. one of the selection of original handles to which we fit a new shaft.Stock Very Limited, 1 Onl
barrel side torpedo solid brass handle, approx 97mm long, supplied with escutcheon. one of the selection of original handles to which we fit a new shaft.Stock Very Limited, 1 pai
barrel side torpedo solid brass handle, approx 92mm long, supplied with escutcheon. one of the selection of original handles to which we fit a new shaft.Stock Very Limited, 1 pai
brass flat top handle, approx 83mm long, supplied with escutcheon. one of the original handles to which we fit a new shaft.1 single in brass only available
chrome external handle with taper and ridge spine to centre. 113mm overall. offered in non locking only. mounting escutcheon 35mm centres.
T boot locking handle approx 95mm long, escutcheon hole centres 44mm, chrome plated. 
chrome plated T locking door handle, 99mm long fitted with mounting escutcheon with 35mm hole centres. particularly suited to van rear doors. shaft will require cutting to suit application. 
solid nickel "T" handle, approx 107mm long, supplied with escutcheon. one of the selection of original handles to which we fit a new shaft.Stock Very Limited, 1 Single Available<
shaped outside handle approx 100mm long fitted with mounting escutcheon, chromium plate finish. offered locking or non locking. we offer this handle with a flat base escutcheon (35mm hole centres) at 
torpedo shape outside handle approx 120mm long, fitted with mounting escutcheon with hole centres approx 34mm. chromium plate finish. please note that these handles are handed. 
concave groove, slightly curved traditional pattern handle, 95mm long. escutcheon hole centres approx 34mm. chromium plate finish. commonly used on Austin 7 and Morgan. 
fluted pattern 115mm long, chrome finish, escutcheon hole centres approx 34mm. 
plain pattern 125mm long, chrome finish, escutcheon hole centres approx 34mm. 
plain pattern 125mm long, chrome finish, escutcheon hole centres approx 34mm. 
fluted pattern 115mm long, chrome finish, escutcheon hole centres approx 34mm. 
chrome plate handle 89mm long with oval escutcheon 23mm x 18mm. short 5/16" (8mm) square shaft. original application bonnet lever handle
handle - interior
interior door handle, to match our 218 winder, chromium finish 114mm long, 3/8"/10mm square shaft size, cross pin fixing. complete with spring loaded escutcheon. handle available without base if requi 
well proportioned slim handle, 122mm long, chrome on brass, fits 5/16"/8mm square shaft. 
large truncheon shape handle approx 120mm long, chrome on brass, suits 5/16"/8mm square shaft. 
medium lever handle approx 105mm long, chrome on brass, suits 5/16"/8mm square shaft. 
small truncheon handle approx 90mm long, chrome on brass, suits 5/16"/ 8mm square shaft. 
small spoon type handle approx 83mm long, chrome on brass, suits 5/16"/8mm square shaft. 
interior door handle to match our window winder handle 539. chromium finish 109mm long, cross pin fixing for 3/8"/10mm square shaft, complete with spring and escutcheon. 
interior lever handle 110mm long, chrome plate, fixed with screw through top. 5/16"/8mm square shaft size, can be fitted at various angles of incline. 
chrome plate on brass lever handle, 120mm long. suits 3/8"/10mm square shaft. 
chrome plate interior lever handle with fixed escutcheon (skirt) 34mm diameter. handle 110mm long, fits over 8mm square shaft and secured with screw through from face. 
chrome plate interior handle 102mm long. 3/8" (10mm approx) hole for square shaft. 
interior door handle 109mm long. cross pin fixing on to 3/8"/10mm square shaft which is set at angle (see picture) to line of handle. chrome plate finish 
chrome plate interior handle for opening sunroof. approx 78mm across, with 35mm diameter base, approx 6mm square shaft hole. handle - pull
4 screw fixing, approx 118mm long, chrome on brass. 
6 screw fixing, approx 144mm long, chrome on brass. 
2 screw fixing, approx 4.6"/ 118mm long, chrome on brass. mounting holes approx 102mm centres.
three legged bonnet handle, particularly suited to larger, heavier bonnets, chromium finish on brass, 5 1/2" x 2 1/4" (140mm x 57mm) 
2 screw fixing, chrome on brass approx 5"/ 125mm long as style fitted to Austin 7 door pull mounting holes approx 110mm centres
4 screw fixing, slim handle approx 4.6" / 118mm long chrome on brass.SOLD OUT 
chrome plate finish large grab handle suitable for mounting to dash etc. hole centres 111mm apart, 140mm long overall. SOLD OUT
chrome plate finish larger grab handle suitable for mounting to dash etc. hole centres 153mm apart, 195mm long overall.
large chrome plate finish larger grab handle suitable for mounting to dash etc. hole centres 209mm apart, 245mm long overall (chrome on brass)
large chrome plate finish larger grab handle suitable for mounting to dash etc. hole centres 250mm apart, 285mm overall
swivel-type grab handle approx 139mm long overall, mounting hole centres approx 120mm, chromium finish. handle - winder
chromium plate finish winder to match our 217 handle. 4.75"/ 120mm long, 3/8"/10mm square shaft size. complete with spring loaded escutcheon. cross pin fixing. winder handle available without base if 
chromium plated window winder with spring loaded escutcheon. overall length approx. 4.3"/ 110mm. 3/8"/10mm square shaft size which fixes with cross pin. winder handle available without base if require 
late vintage period reproduction chrome (nickel plate offered as an alternative) on brass window regulator handle, 103mm long overall. rear locating boss 20mm diameter which fits over 10mm round shaft 
chrome plated fluted design interior winder handle approx 90mm long with chrom plate knob. 3/8" (10mm approx) hole for square shaft our escutcheon 219 will fit this handle but will require easing as very tight.
hinge
brass butt hinge, 63mm high x 55mm closed, with drilled flaps. this hinge measures only 10mm across the knuckle. limited quantity. 
heavy brass door hinge, undrilled flaps. 2 1/2" high x 4" wide (approx 63mm x 100mm) when closed. 5 equal knuckles, 1/2" (12.5mm) parallel sided for the pin, material thickness 5mm at open end of hing 
chrome plated boot or bonnet hinge with securing studs on rear to fit through panel. used on Lotus Elan, TVR. Hillman Imp, Reliant and kit cars. base 135mm x 22mm overall. three securing studs, suppli 
chrome plated hinge with securing studs on rear to fit through panel. used as original part on Morris Minor as boot hinge. base 212mm x 22mm overall. three securing studs, supplied with nuts. NOTE th 
chrome plated boot or bonnet hinge with securing studs on rear to fit through panel. used on Triumph TR4, Spitfire, Herald, Nash Metropolitan, Standard 8 & 10. base 123mm x 22mm overall. three securin 
chrome plated hinge with securing studs on rear to fit through panel. used as original part on Morris Minor 1951 onward as bonnet hinge. base 191mm x 26mm overall. four securing studs, supplied with n 
solid brass undrilled, steel pin, flap size 1 3/4" high x 4" long (approx 45mm x 100mm) when closed. 5 equal knuckles, 1/2" (12.5mm) parallel sided for the pin, material thickness 5mm at open end of 
solid brass undrilled, steel pin, flap size 1 3/4" high x 2" wide (approx 45mm x 50mm) when closed. 5 equal knuckles, 1/2" (12.5mm) parallel sided for the pin, material thickness 5mm at open end of hi 
solid brass undrilled, steel pin. flap size 1 1/2“ high x 2" wide (approx 38mm x 50mm) when closed. 5 equal knuckles, 1/2" (12.5mm) parallel sided for the pin, material thickness 5mm at open end of hi 
solid brass undrilled, steel pin, flap size 1 1/2“ x 4". (approx 38mm x 100mm) when closed. 5 equal knuckles, 1/2" (12.5mm) parallel sided for the pin, material thickness 5mm at open end of hinge. 
solid brass undrilled, steel pin, flap size 2" high x 4" wide (approx 50mm x 100mm) when closed. 5 equal knuckles, 1/2" (12.5mm) parallel sided for the pin, material thickness 5mm at open end of hinge 
solid brass undrilled, steel pin. flap size 1 1/8“ high x 2" wide (approx 28mm x 50mm) when closed. 3 knuckles, 1/2" (12.5mm) parallel sided for the pin, material thickness 5mm at open end of hinge. 
replacement 19mm diameter brass conical ball for self aligning hinge 
replacement spherical brass hinge pin ball, 5/8" (16mm) diameter 
replacement spherical brass hinge pin ball, 3/4" (19mm) diameter 
replacement brass half ball (19mm diameter) with hexagon base (11.6mm across flats) for steel self align hinges. 
cast iron type van door hinge 80mm wide x 76mm tall. left hand and right hand available. (note illustration shows left hand part) 
larger cast iron type van door hinge 125mm wide x 102mm tall. left hand and right hand available. (note illustration shows left hand item) 
large cast iron type van door hinge 150mm wide x 102mm tall. left hand and right hand available. (note illustration shows left hand item). only 1 pair of this part 
cast iron type van door hinge 86mm wide x 85mm tall. left hand and right hand available. (note illustration shows left hand item) 
replacement hinge pin, spring, tag washer and nut for 51mm tall steel self aligning hinge. pin measures approx 6mm diameter x 62mm long. note that these are made to imperial sizes and thread. order br 
replacement hinge pin, spring, tag washer and nut for 38mm tall steel self aligning hinge. order brass ball separately. 
self aligning iron van door hinge 66mm tall x 57mm wide. left hand and right hand available. (note illustration shows right hand part). note that the weight of the door is always carried in the cup NO 
self aligning iron van door hinge 112mm high. left hand and right hand. overall 110mm wide.mounting hole centres 76mm tall and 54mm wide.
2 PAIRS ONLY AVAILABLE - sold as one lot only
self aligning steel - self colour. flaps undrilled, size 2" x 5" (approx 50mm x 125mm) left hand and right hand. note the swinging part sits on ball which sits in the cup of the fixed part (note illu 
self aligning steel - self colour. flaps undrilled, size 1 1/2" 38mm(Pin) x 1 7/8" 49mm(Flap)LEFT hand ONLY. note the swinging part sits on ball which sits in the cup of the fixed part hood frame
steamed ash section 32mm x 25mm, inside radius of bend 125mm. we stock these sticks in 'half hood stick' form for immediate delivery. 2 sticks are mitred together, glued and screwed, to make the compl 
D shaped tube approx 19mm x 10mm x 1.5mm wall thickness. stock lengths approx 2 metre to ease bending the flat side needs to be depressed inwards at point or radius.
hood frame - window
brass extrusions of sectioned half round and rectangular strip for DIY hood rear window frame manufacture, 1230mm lengths only. 
hood window frame to fit into the back of convertible hoods. a period fitting rather than using flexible vyback. we manufacture in one standard size of approx 460mm x 150mm, but specials can be made t lift rings
cast iron screw with cup on to angled bracket, a very firm floor attachment method. screw cup 57mm diameter 
rectangular, size 64mm x 43mm, without lock, chrome on brass. 
round, diameter 51mm, chrome on brass. 
rectangular mounting, size 51mm x 38mm with lift ring lock catch, self colour brass. 
rectangular mounting, size 64mm x 45mm with lift ring lock catch, chrome. mesh
brass double crimp wire mesh on DIAGONAL weave, 16swg (1.63mm) wire, approx 12mm aperture, for radiator stoneguards etc. sheet size 600mm x 800mm
brass double crimp wire mesh on DIAGONAL weave, 16swg (1.63mm) wire, approx 12mm aperture, for radiator stoneguards etc. sheet size 500mm x 600mm 
brass double crimp wire mesh 16swg (1.63mm), approx 12mm aperture for making radiator and headlamp stoneguards. we stock this in approx 1.86m x 1.23m sheets (square format) but we cut to smaller piec full sheet are available at discounted price, please contact us for details.
over-ride bead
bumper over-rider bead, black plastic, approx 10mm wide base with 2mm slot. 
bumper over-rider bead, black PVC, approx 4.5mm diameter. seat runner
universal application, plated finish. allow seat adjustment forward and backward, with secure locking lever. base 470mm long. per seat set. 
universal application, stainless steel, seat runner actually on rollers with X brace fitted. easy forward and backward movement, base approx 550mm long x 295mm wide. per seat set. sidescreen
screw/spade type, screw fitting (knob 28mm dia) only supplied which clamps on to blade on sidescreen. triangular base 53mm x 34mm fixing, chromium finish. 
8mm diameter,40mm long peg,base 46mm x 14mm,with 33mm hole centres chrome on brass. 
socket for 8mm diameter peg. 36mm long, head 14mm dia, 11mm hole required in bodywork. chrome on brass. tread strip
moulded aluminium running board strip supplied with black rounded rubber tread filler insert. available in cut lengths as follows:910mm long at £7.23 each
1220mm long at £9.64 each
1820mm long at
moulded aluminium running board strip supplied with black ribbed rubber tread filler insert. available in cut lengths as follows:910mm long at £7.23 each
1220mm long at £9.64 each
1820mm long at £
this pattern usually used on Jaguar, SS and Riley motors.
moulded aluminium running board strip supplied with black rounded rubber tread filler insert. available in cut lengths as follows:910mm long at £7.71 each
1220mm long at £10.28 each
1820mm long at
moulded aluminium running board strip supplied with black rounded rubber tread filler insert. approx height when fitted together 12mm. available in cut lengths as follows:910mm long at £9.66 each
1
pressed aluminium end cap to cover end of 22mm wide tread strip (237) with rubber insert. can be nipped together to be used on 19mm wide strip (283) if required. 
cast chrome on brass end cover plate, supplied with a drill hole. the finishing end for aluminium/rubber treads. specify size required. tread strip - filler
black rounded rubber tread filler for 22mm wide aluminium strip. approx 16mm wide across base, 14mm wide neck, 9.2mm tall approx 
black rounded rubber tread filler for 16mm wide aluminium strip. 11.2mm wide across base, 8.5mm wide neck, 7.3mm tall approx 
black rounded rubber tread filler for 19mm wide aluminium strip. approx 14.5mm wide across base, 13.1mm wide neck, 9.0mm tall approx 
black ribbed rubber tread filler for 16mm wide aluminium strip. 11.0mm wide across base, 8.5mm wide neck, 7.0mm tall approx ventilators
circular hit and miss type ventilators available in chromiun plate on brass or self colour brass finishes. adjust by twist fly nut. 93mm diameter chrome plate on brass - £13.50 each
125mm diameter
medium rectangular louver ventilator for scuttle mounting. overall size 8" x 4" (203mm x 101mm) with gauze as standard, opens to one side against spring. we offer a choice of materials and finishes:if only one piece required please order 0.5 pair
small rectangular louver ventilator overall for scuttle mounting. overall size 6” x 3" (152mm x 76mm) with gauze as standard, opens to one side against spring. we offer a choice of materials and fini if only one piece required please order 0.5 pair
large rectangular louver ventilator for scuttle mounting. overall size 250mm x 113mm with gauze. opens to one side against spring. offered in zinc plate on steel.other ventilators available see if only one piece required please order 0.5 pair
medium rectangular louver ventilator for scuttle mounting. overall size 8" x 4" (203mm x 101mm) without gauze, opens to one side against spring, pull knob on outside. body is chrome OR nickel plate on window channel
rigid single channel felt/rubber/moquette lined, approx 14mm wide x 12.5mm high, glass 4.7mm to 6.4mm. 2 metre length only.please note that if buyers can specify cutting lengths - savings on carri
velvet lined rubber, for 4.5mm glass, overall width 12mm x height 13mm. flexible channel. wholesale prices apply on roll approx 20 metres. discount on application.
velvet lined rubber, for 4.5mm glass, overall width 10mm x height 10mm. flexible channel. wholesale prices apply on roll approx 20 metres. discount on application.
velvet lined rubber, for 6mm glass, overall width 14.5mm x height 13.5mm. flexible channel. wholesale prices apply on roll approx 20 metres. discount on application.
rigid aluminium channel (approx 14mm wide x 15mm deep) with black felt insert, for 6mm glass. available in cut lengths of 1metre, 1.5metre or 2metre only.our part 263 velvet channel can be ordered s
flexible metal single channel, felt/rubber/moquette lined, overall width approx 14.5mm, height 13mm. glass thickness 4.7mm to 6.4mm. black woven edge. wholesale prices apply on roll approx 20 metres. discount on application.
stainless steel edged flexible metal channel suitable for 4.5mm to 6mm thick glass, outside dimensions approx 16mm wide x 15mm deep. suits Rover, Morris Traveller etc. available in 2760mm length only ... 
universal flexible rubber channel, flock finish inside, will suit 4.5mm or 6mm glass, and can be made to fit variations of holder, to fit nominal width 13mm channel wholesale prices apply on roll approx 15 metres. discount on application.
velvet lined double width rubber, for 6mm glass, overall width 24mm x height 13mm. flexible channel. discount available on 20 metre rolls
velvet lined double width rubber, for 5mm glass, overall width 22mm x height 13mm. flexible channel. discount available on 20 metre rolls
universal flexible rubber channel, flock finish inside, will suit 4.5mm or 6mm glass, and can be made to fit variations of holder, to fit nominal width 13mm channel wholesale prices apply on roll approx 15 metres. discount on application.
10mm (internal) wide folded steel channel will suit most applications, zinc plated finish. this is offered in lengths of 600mm only and suitable for both single and double roller window lifter arms. window weatherstrip
wipe/seal for sliding windows, rigid carrier with fur on one outer edge to seal between passing windows. cut to specific length (units 0.10m). dimensions glass gap 6.25mm, overall 10.9mm deep x 17mm w 
exterior weatherstrip, smaller version of our range, seals 10mm body/glass gap, 1 metre lengths only.depth of vertical approx 10mm.
weatherstrip for exterior or interior use. fitted between the door and the opening window glass. 17mm high, 5mm deep, with galvanised edge bead, one side plush fur pile finish. available in 2 metre le
exterior weatherstrip, to fit the outside edge of opening window glass, rubber with felt face, metal stiffener strip, seals up to 11mm body/glass gap. 1 metre lengths only. depth of vertical approx 18
weatherstrip for exterior or interior use, fits between door and drop window glass, narrow version, 11.5mm high, 7mm thick. often used on early Ford, lengths available 8ft/2.44m at £13.98 or 4ft/1.21m 
early vintage weatherstrip which fits horizontally under door capping. black velvet covered rubber - specify lengths required (maximum in one piece 2 metres). wing piping
leathercloth covered fender welt, stitched over plastic cord centre, black dull grained finish, approx 6mm diameter bead, 32mm flange
leathercloth covered fender welt, stitched over plastic cord centre, dull grained finish, black only. approx 8mm diameter, 32mm flange, we can make other sizes of piping to order, minimum 10 metres,
leathercloth covered fender welt, stitched over plastic cord centre, dull grained finish, approx 4mm diameter, 32mm flange, black only.
leathercloth covered fender welt, stitched over plastic cord centre, dull grained finish approx 6mm diameter bead, 32mm flange - stocked in following colours - green, grey, blue, maroon, ivory, fawn, 
hollow bead black plastic piping. use between wing (fender) and body (fender welt), available in the following sizesdiscounted
leathercloth covered fender welt, stitched over plastic cord centre, bright (shiny) patent-look finish, black only. -approx 6mm diameter bead, 32mm flange
leathercloth covered fender welt, stitched over plastic cord centre, bright (shiny) patent-look finish, black only. approx 8mm diameter, 32mm flange
leathercloth covered fender welt, stitched over plastic cord centre, bright (shiny) patent-look finish, black only. approx 4mm diameter, 32mm flange 
solid bead plastic, approx 6mm diameter 25mm flange, stocked in the following colours. black, blue, green, red and tan. 
half-round plastic T piping, 6mm wide bead, 16mm ribbed flange, stocked in black, white or silver grey.